1255 - Instructions

All Instructions for the 1255
46 - 60 of 109

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not drain
1 person found this instruction helpful.
  • Robert from SANDWICH, IL
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Blown element
1 person found this instruction helpful.
  • Kathy from SANDYSTON, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Very easy. Didn't have to replace whole unit
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person found this instruction helpful.
  • Michael from Thornton, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this helpful?
Thank you for voting!
replace element
1 person found this instruction helpful.
  • alex from huntington, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Burnt out
2 of 4 people found this instruction helpful.
  • David from Elba, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person found this instruction helpful.
  • Helen from SPRINGFIELD, OH
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person found this instruction helpful.
  • Victor from NORFOLK, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
Baking element popped
2 of 4 people found this instruction helpful.
  • Jerry from Rancho Cordova, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This was too simple, turned off the power to the oven, undid the two screws, unplugged two wires, plugged wires into the new element, fastened the new screws and turned the power back on. Turned on the oven, what do you know, it works again!

The element did not come with instructions and none were needed.
Was this helpful?
Thank you for voting!
Lower element was broken.
1 of 2 people found this instruction helpful.
  • Daniel from Wilmington, DE
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Awesome, just awesome, you guys are great and I will use you again and again.
Was this helpful?
Thank you for voting!
burned out element
1 of 2 people found this instruction helpful.
  • Richard from Highland Village, TX
  • Easy
  • Less than 15 mins
  • Screw drivers
This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because wit h the element out, it's easy to do.
Was this helpful?
Thank you for voting!
oven element not wrk'n
1 of 2 people found this instruction helpful.
  • Debbie from MT.VERNON, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin
Was this helpful?
Thank you for voting!
took to long to preheat and food wasn't cooked on the bottom
1 of 2 people found this instruction helpful.
  • Jessica from Lubbock, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!
Was this helpful?
Thank you for voting!
Bake Element burned out
1 of 2 people found this instruction helpful.
  • John from Lincoln Park, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.
Was this helpful?
Thank you for voting!
Element Got Corroded Then Failed (Broken)
1 of 2 people found this instruction helpful.
  • Tom from Lancaster, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Connected the wires to new element, pushed wires back into the back wall, re-installed screws.
Was this helpful?
Thank you for voting!
Thermostat bulb was hanging loose
2 of 5 people found this instruction helpful.
  • Willi from Old Saybrook, CT
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this helpful?
Thank you for voting!
All Instructions for the 1255
46 - 60 of 109