1255 - Instructions

Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.

I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.

1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. ... Read more 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.

Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with nor ... Read more mal tools.Thanks

turned off power unscrewed plate that held in element unplugged socket from old element plugged in new one screwed plate back turned on power works fine

Changed bake element in oven.

Turned breaker off. Took out two screws holding it in place. Disconnected two wires. Put new element in. Works fine

Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.

First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly ... Read more easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.

Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed ... Read more the previous procedures to complete repair.

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. al ... Read more most spent $400.00 on a new one.

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c ... Read more an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.