1151 - Instructions

All Instructions for the 1151
46 - 60 of 99

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip bowls very dirty and stained
1 of 2 people found this instruction helpful.
  • john from donna, TX
  • Really Easy
  • Less than 15 mins
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ses were simple and delivery was faster than I hed expected.
Thank you
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people found this instruction helpful.
  • Michael from Portland, OR
  • Really Easy
  • Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
Burner plugs were loose
1 of 2 people found this instruction helpful.
  • James from CONCORD, NC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
used the supplied parts...very easy. The parts were exact replacements.
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 people found this instruction helpful.
  • Robert from Birmingham, AL
  • Easy
  • 15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this helpful?
Thank you for voting!
Receptacle had become bad poor connection.
1 of 3 people found this instruction helpful.
  • JAMES from Harrodsburg, KY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.
Was this helpful?
Thank you for voting!
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
1 of 3 people found this instruction helpful.
  • shawn from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Pliers
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Was this helpful?
Thank you for voting!
replace coroded drip pans
1 of 3 people found this instruction helpful.
  • Marlin F. from Holbrook, AZ
  • Really Easy
  • Less than 15 mins
replaced the drip pans. Fit perfect. No problems
Was this helpful?
Thank you for voting!
Sockets for the burner elementss were burned out
0 of 1 people found this instruction helpful.
  • Martin from Manchester, MD
  • Really Easy
  • 15 - 30 mins
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Was this helpful?
Thank you for voting!
Bowl -Drip and gasket
0 of 1 people found this instruction helpful.
  • Walid from Worcester, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid
Was this helpful?
Thank you for voting!
Ugly looking drip bowl.
0 of 1 people found this instruction helpful.
  • Irina from Green Cove Springs, FL
  • Really Easy
  • Less than 15 mins
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this helpful?
Thank you for voting!
one of wire melted and broken off from receptacle
0 of 1 people found this instruction helpful.
  • Young from Cordova, TN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.
Was this helpful?
Thank you for voting!
Electrical receptacle for burner was defective.
0 of 1 people found this instruction helpful.
  • gerald from Hillsboro, TN
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short t ime to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.
Was this helpful?
Thank you for voting!
Burner element stopped working
  • Robert from Lodi, CA
  • Really Easy
  • 1- 2 hours
  • Screw drivers
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.
Was this helpful?
Thank you for voting!
Cartridge wire burned out
  • Robert from San Francisco, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Was this helpful?
Thank you for voting!
unable to remove screw with screwdriver
  • Emmett from Rayville, LA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
used drill to remove old screw
Was this helpful?
Thank you for voting!
All Instructions for the 1151
46 - 60 of 99