110885 Kenmore Dryer - Instructions

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

I replaced the push start buttom,but it still had the same problem,so I went to the motor and found the burnt wire and bingo,we are happy again thanks to your website.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t ... Read more o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un ... Read more thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

removed the back of the dryer and the thermal fuse and the dryer cycling thermostat were right next replace them and the dryer work like new my dryer is 40 years old and saved a ton of money fixing it myself

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

replace basket with new one snapped in

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one ... Read more on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an ... Read more d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Popped out the old lent trap & popped in the new one..and walla perfect repair..