110885 Kenmore Dryer - Overview

Models starting with 110885

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Thermal Fuse – Part Number: WP3392519
$25.19
In Stock
Dryer Thermal Fuse
★★★★★
★★★★★
(149)
Part #WP3392519
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when there is no longer continuity between the pins. Terminal size is 3/16".
Door Catch Kit – Part Number: 279570
$10.58
In Stock
Door Catch Kit
★★★★★
★★★★★
(87)
Part #279570
This kit contains two door strikes, and three door catches to service dryer doors that have one or two catches.
Rear Drum Support Roller Kit – Part Number: 349241T
$29.23
In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(63)
Part #349241T
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing all necessary components for a complete replacement. The rollers support the drum as it rotates, and worn or damaged rollers can cause excessive noise, poor tumbling performance, or even leave marks on clothing. Replacing these components can resolve issues such as rumbling, squealing, or grinding sounds during operation. Compatible with many units from Whirlpool, Kenmore, Sears, and other brands, this kit offers a reliable solution for maintaining optimal dryer performance.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Drive Motor with Pulley – Part Number: 279827
$151.26
In Stock
Drive Motor with Pulley
★★★★★
★★★★★
(29)
Part #279827
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers the drum by turning the belt, helping your clothes dry properly. Just make sure to unplug the dryer before starting the repair. Once installed, your dryer should be back to working like new.
Dryer Lint Filter and Cover – Part Number: W10828351
$77.53
In Stock
Dryer Lint Filter and Cover
★★★★★
★★★★★
(24)
Part #W10828351
This dryer lint filter and screen assembly is a genuine replacement part designed to trap lint and fibers during the drying cycle, helping to maintain airflow and prevent blockages in the vent system. Its kidney-shaped screen is constructed from durable steel and ABS plastic, housed within a cover that features four metal clips for secure installation. By capturing debris, it supports efficient drying times and reduces the risk of overheating or fire hazards. Compatible with various Whirlpool, Kenmore, and associated brand dryers, this OEM part replaces several previous versions and ensures a precise fit. Regular inspection and replacement of the lint filter are recommended to maintain optimal dryer performance.
Dryer Idler Pulley Assembly – Part Number: WP691366
$24.19
In Stock
Dryer Idler Pulley Assembly
★★★★★
★★★★★
(2)
Part #WP691366
The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.
Heating Element Connection Wire Kit – Part Number: 279457
$13.97
In Stock
Heating Element Connection Wire Kit
★★★★★
★★★★★
(4)
Part #279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
Door Catch – Part Number: WP3389441
$14.95
In Stock
Door Catch
★★★★★
★★★★★
(8)
Part #WP3389441
This white female door catch is attached to the dryer door.
Dryer Door Switch Actuator – Part Number: WP691581
$14.95
In Stock
Dryer Door Switch Actuator
★★★★★
★★★★★
(10)
Part #WP691581
This black actuator spring with white rubber tip is used for both dryer doors and washer lids.
Lid Switch – Part Number: W10820036
$33.28
In Stock
Lid Switch
★★★★★
★★★★★
(7)
Part #W10820036
Keep your washer or dryer running safely with this easy-to-install lid or door switch kit. It stops the machine from working when the door is open, helping prevent spills and accidents. Compatible with many models, this small but important part fits neatly inside your appliance and comes with everything you need for installation. Just unplug your machine, swap out the old switch, and you're good to go. It’s about 2.5 inches long and blends in with most interiors.
Dryer Lint Trap Housing Seal – Part Number: WP339956
$15.95
In Stock
Dryer Lint Trap Housing Seal
★★★★★
★★★★★
(4)
Part #WP339956
This seal comes with the adhesive backing.

Exact Part matches for your search term

USE PRO TJ110885 – Part Number: 110885
No Longer Available
USE PRO TJ110885
This part number matches the current model number 110885
Part #110885

Common Symptoms of models starting with 110885

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was working, but no heat.
3070 of 3494 people found this instruction helpful.
  • ANTHONY from CHESHIRE, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Was this helpful?
Thank you for voting!
No heat but would run otherwise
928 of 1024 people found this instruction helpful.
  • Dana from Grassvally, CA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and did n't take but 15-20 minutes.
Was this helpful?
Thank you for voting!
Door Catch part had fallen out,/ was missing
676 of 740 people found this instruction helpful.
  • Terri from Saint Augustine, FL
  • Really Easy
  • Less than 15 mins
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
Was this helpful?
Thank you for voting!