110877 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people
found this instruction helpful.
-
Eric from West Chester, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Close would not get dry. Dryer started normal. Timer would not time out.
12 of 18 people
found this instruction helpful.
-
Roger from Westminster, SC
- Very Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of t
... Read more
he door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.
The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.
I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).
The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.
I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people
found this instruction helpful.
-
stephen from langley, KY
- Really Easy
- Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
Replaced a broken pulley.
10 of 12 people
found this instruction helpful.
-
Brian from IMLAY CITY, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people
found this instruction helpful.
-
Michael from ENOLA, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Other Parts Used:
Was this helpful?
Thank you for voting!
Gas Dryer would heat for one heating cycle but no gas afterward. Ignitor would glow.
10 of 12 people
found this instruction helpful.
-
Jim from Foothill Ranch, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h
... Read more
e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.
Read less
Was this helpful?
Thank you for voting!
Old motor was making noise and tripping after a few minutes
10 of 13 people
found this instruction helpful.
-
John from Midland, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people
found this instruction helpful.
-
Theresa from Norfolk, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
No heat in dryer
10 of 14 people
found this instruction helpful.
-
Noah from Maiden, NC
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Was this helpful?
Thank you for voting!
No Heat
9 of 12 people
found this instruction helpful.
-
NICHOLAS from PARMA, OH
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (i
... Read more
t should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.
Read less
Was this helpful?
Thank you for voting!
Dryer was working but not generating heat.
8 of 9 people
found this instruction helpful.
-
Laurie from Natick, MA
- Easy
- 15 - 30 mins
-
Screw drivers
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hose
... Read more
s. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
Read less
Was this helpful?
Thank you for voting!
dryer would not heat or turn off
9 of 12 people
found this instruction helpful.
-
michael from eldridge, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.
Was this helpful?
Thank you for voting!
No heat
9 of 13 people
found this instruction helpful.
-
Philip from La Palma, CA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!
Was this helpful?
Thank you for voting!
Dryer hummed but drum wouldn't turn unless helped.
8 of 10 people
found this instruction helpful.
-
Leo from Ellicott City, MD
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part
... Read more
was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Read less
Was this helpful?
Thank you for voting!