110877 Kenmore Dryer - Instructions

All Instructions for the 110877
121 - 135 of 1053

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer not Drying
8 of 10 people found this instruction helpful.
  • Manuel from Jurupa Valley, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.
Was this helpful?
Thank you for voting!
No heat
9 of 13 people found this instruction helpful.
  • Philip from La Palma, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!
Was this helpful?
Thank you for voting!
Dryer hummed but drum wouldn't turn unless helped.
8 of 10 people found this instruction helpful.
  • Leo from Ellicott City, MD
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Was this helpful?
Thank you for voting!
Dryer would not turn on
8 of 10 people found this instruction helpful.
  • Pam from Chandler, AZ
  • Really Easy
  • Less than 15 mins
  • Socket set
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!
Was this helpful?
Thank you for voting!
The dryer door latch broke
9 of 13 people found this instruction helpful.
  • Theresa from Topeka, KS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Was this helpful?
Thank you for voting!
no heat was being produced
9 of 14 people found this instruction helpful.
  • reinaldo from guttenberg, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this helpful?
Thank you for voting!
No Heat After 10 Minutes
7 of 8 people found this instruction helpful.
  • lawrence from GROTON, VT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench set
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this helpful?
Thank you for voting!
My Kenmore dryer door catch was worn out, so the dryer door wouldn't stay closed, and I was unable to dry my laundry.
8 of 11 people found this instruction helpful.
  • Carol from Golden Valley, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.
Was this helpful?
Thank you for voting!
Dryer wouldn't start
10 of 17 people found this instruction helpful.
  • Ryan from Mundelein, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 busine ss days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!
Was this helpful?
Thank you for voting!
the glow ignitor would not cycle on
7 of 8 people found this instruction helpful.
  • Georgio from Oradell, NJ
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the g low plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.
Was this helpful?
Thank you for voting!
Broken Door Handle on Front of Dryer
13 of 26 people found this instruction helpful.
  • Jeff from Wausau, WI
  • Really Easy
  • Less than 15 mins
Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.

Thanks for the great service.
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people found this instruction helpful.
  • Joseph from Austin, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Was this helpful?
Thank you for voting!
My dryer conked. Would not turn on, but before that happened it was taking way too long to dry the clothes and the dryer would stop in the middle of a cycle.
7 of 9 people found this instruction helpful.
  • brenda from Newman Lake, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519
Was this helpful?
Thank you for voting!
Broken Belt
7 of 9 people found this instruction helpful.
  • Ken from LOMBARD, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent
Was this helpful?
Thank you for voting!
Dryer does not heat but blows only cold air
6 of 6 people found this instruction helpful.
  • kevin from RENTON, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch
Was this helpful?
Thank you for voting!
All Instructions for the 110877
121 - 135 of 1053