110877 Kenmore Dryer - Instructions

All Instructions for the 110877
76 - 90 of 1053

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer working fine but no heat
18 of 22 people found this instruction helpful.
  • Cornelius from ELKO, GA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Found this website and reviewed videos and comments prior to purchasing the heater element and high limit thermostat and thermal fuse kit. We had recently put our Whirlpool duet washer and dryer on pedestals and after that, the dryer would come on and run, but would not heat up. Installation of the parts we ordered was simple...and we w ould be considered novice installers....really great website and easy to understand. Customer service was excellent as well. After installation of the parts, still no heat and heating element was registering only 120v. We checked everything again and found that the dryer plug was not all the way in the socket. Probably came loose with the move to the petestal.....plugged it in securely and it works great now. Should have checked that first, but because it was running we just didn't think of checking it. Good lesson learned and so glad we found this website. We will definately be using this site again and telling everyone we know about how great you guys are! And at least we won't have to worry about the dryer for a while and we now know we can fix a dryer that won't heat up!
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people found this instruction helpful.
  • rodney from Mad River, CA
  • Very Difficult
  • More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people found this instruction helpful.
  • Rebecca from Laredo, TX
  • Really Easy
  • Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
16 of 17 people found this instruction helpful.
  • Victor from HOUSTON, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the b roken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people found this instruction helpful.
  • Xiaobin from Cordova, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people found this instruction helpful.
  • Mandie from Lewisville, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The swit ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Was this helpful?
Thank you for voting!
Flashing E1 code for a bad thermistor
19 of 28 people found this instruction helpful.
  • John from Cedar Rapids, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. A lso, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.
Was this helpful?
Thank you for voting!
Placing Dryer on Top of Washing Machine with Stack Kit
25 of 46 people found this instruction helpful.
  • Randy from Brentwood, CA
  • Really Easy
  • 15 - 30 mins
  • Wrench set
I purchased a stack kit from "Part select.com". The item was just what I needed to do the job. The delivery of the part was made the next morning. WOW! Excellent service! The process was completed in less than 24 hours, start to finish. Very impressed!
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people found this instruction helpful.
  • John from Midland, TX
  • Really Easy
  • Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people found this instruction helpful.
  • Lynne from Jamestown, CA
  • Really Easy
  • Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people found this instruction helpful.
  • Kim K from Hurst, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Was this helpful?
Thank you for voting!
Loud sreeching and vibration
14 of 15 people found this instruction helpful.
  • Robert from TUTTLE, OK
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people found this instruction helpful.
  • PHILIP from LONG ISLAND CITY, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people found this instruction helpful.
  • Brad from Odessa, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.

Thanks for the help.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people found this instruction helpful.
  • Richard from SAUGERTIES, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
All Instructions for the 110877
76 - 90 of 1053