11087402 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud squealing when the dryer was running...especially on start up.
4 of 6 people
found this instruction helpful.
-
Anthony from GROVELAND, IL
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pul
... Read more
ley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.
Read less
Was this helpful?
Thank you for voting!
Intermittent squealing sound while dryer running
4 of 6 people
found this instruction helpful.
-
John from LAKE ZURICH, IL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of ... Read more the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of ... Read more the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel
Read less
Was this helpful?
Thank you for voting!
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
3 of 3 people
found this instruction helpful.
-
Lawrence from ARITON, AL
- A Bit Difficult
- More than 2 hours
-
Screw drivers, Socket set
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to
... Read more
be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
Read less
Was this helpful?
Thank you for voting!
Making a racket.
3 of 3 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this helpful?
Thank you for voting!
No heat
4 of 7 people
found this instruction helpful.
-
James from Randsburg, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with
... Read more
the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke
Read less
Was this helpful?
Thank you for voting!
Dryer motor bearings failed. Motor wouldn't start.
8 of 19 people
found this instruction helpful.
-
Mark from Maple Valley, WA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way.
... Read more
The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
Read less
Was this helpful?
Thank you for voting!
belt was cracking and dryer was somewhat noisy
4 of 7 people
found this instruction helpful.
-
Melody from Silverton, CO
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol
... Read more
ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Read less
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people
found this instruction helpful.
-
Cynthia M from Westfield, MA
- Easy
- More than 2 hours
-
Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too
... Read more
shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people
found this instruction helpful.
-
Steven from WICHITA, KS
- Really Easy
- 30 - 60 mins
-
Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
Belt Broken
2 of 2 people
found this instruction helpful.
-
Gus from RIVERSIDE, CA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Watched video & took my time. It went easy
Was this helpful?
Thank you for voting!
Lights turn on, all the beeps but dryer won't start.
2 of 2 people
found this instruction helpful.
-
James from HONESDALE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the wrong part. It was pick and choose from the info provided.I checked again and found one that's 58% of the time the part.
Was this helpful?
Thank you for voting!
The bearing on the idler pulley went bad, squealing
2 of 2 people
found this instruction helpful.
-
Gerald from Yucaipa, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took the dryer apart and replaced the idler pulley with bracket and the drive belt
Other Parts Used:
Was this helpful?
Thank you for voting!
Idler Pulley squealing - Worn out
2 of 2 people
found this instruction helpful.
-
Thomas E from PERRYSBURG, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back ... Read more on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back ... Read more on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!