11087402 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No heat, would not light because igniter burnt out
6 of 8 people
found this instruction helpful.
-
anthony from Port Arthur, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr
... Read more
ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Read less
Was this helpful?
Thank you for voting!
Noisy
5 of 5 people
found this instruction helpful.
-
Robert from HAGERSTOWN, MD
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retain
... Read more
er clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Read less
Was this helpful?
Thank you for voting!
Dryer was Noisy
6 of 8 people
found this instruction helpful.
-
Doug from HARRODSBURG, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back ... Read more and two in the front.
A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.
It was an easy fix, I just did half the install a second time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint filter seal worn out
5 of 5 people
found this instruction helpful.
-
Dennis from PALM BCH GDNS, FL
- Very Easy
- Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
Drum support roller making very loud noise
5 of 5 people
found this instruction helpful.
-
William from TROY, AL
- Really Easy
- 1- 2 hours
-
Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer made squeaking noise, then more of a rumbling noise.
5 of 6 people
found this instruction helpful.
-
JAMES from NORTH OLMSTED, OH
- A Bit Difficult
- 1- 2 hours
-
Pliers, Socket set, Wrench set
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pul
... Read more
ley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Idler pulley seized
4 of 4 people
found this instruction helpful.
-
John from CREST HILL, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and rem
... Read more
ove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Read less
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people
found this instruction helpful.
-
Kevin from VALDOSTA, GA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people
found this instruction helpful.
-
Charles from Long Beach, CA
- Easy
- 30 - 60 mins
-
Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people
found this instruction helpful.
-
Paul from STONE CREEK, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Unit not spent
4 of 4 people
found this instruction helpful.
-
Boonkham from SMYRNA, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Just replaced part
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Drum Belt
4 of 4 people
found this instruction helpful.
-
Garry from Garland, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Just like the video, just followed the video
Thanks,
Thanks,
Was this helpful?
Thank you for voting!
My idler pully was squealing
4 of 5 people
found this instruction helpful.
-
Anthony from SAINT CLOUD, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it
... Read more
took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Read less
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people
found this instruction helpful.
-
Anthony from PITTSTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered
... Read more
a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Read less
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!