11087402 Kenmore Dryer - Instructions

All Instructions for the 11087402
121 - 135 of 354

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Very loud squeaking!
2 of 2 people found this instruction helpful.
  • Travis from GARRETT, IN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
Was this helpful?
Thank you for voting!
Dryer stopped working.
3 of 5 people found this instruction helpful.
  • Andrew from Edina, MN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.
Was this helpful?
Thank you for voting!
No leveling feet on dryer.
2 of 2 people found this instruction helpful.
  • Bobbie from BEND, OR
  • Very Easy
  • Less than 15 mins
  • Wrench (Adjustable)
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this helpful?
Thank you for voting!
Broken belt
2 of 2 people found this instruction helpful.
  • Robert from CALIFORNIA, MO
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Disconnect gas line and vent hose,removed top and back covers to install belt.
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people found this instruction helpful.
  • Susan from WARREN, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
electric dryer stopped heating - the thermostat got very hot
4 of 8 people found this instruction helpful.
  • Ignas from Midpines, CA
  • Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find whe re they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people found this instruction helpful.
  • Carl from MARION, KY
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
Dryer was making a loud squeaking noise
2 of 2 people found this instruction helpful.
  • James from Toccoa, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the video instructions. I took my time as this was a first for me. The disassembly was fairly straightforward. The belt idler pulley was definitely the problem as it wouldn’t turn at all. I decided to replace the support rollers also even though they seemed to be ok. Everything I had read said my model only needed 4 rollers bu t actually needed 6. I had to place a second order for those. Putting it all back together was fairly easy. Overall I had a good experience. Only a few tools were needed for this repair. Thank you,
Was this helpful?
Thank you for voting!
Bad Motor, Would not start.
3 of 5 people found this instruction helpful.
  • Steve from S LAKE TAHOE, CA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Was this helpful?
Thank you for voting!
The original motor stopped working
2 of 2 people found this instruction helpful.
  • Robert from PFLUGERVILLE, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexib le dryer tube since the old one had a few holes. It works perfectly again.
Was this helpful?
Thank you for voting!
The dryer would not heat up
3 of 6 people found this instruction helpful.
  • William from Canyon Country, CA
  • Difficult
  • 1- 2 hours
  • Screw drivers, Wrench set
I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...
Was this helpful?
Thank you for voting!
Dryer electrically dead
3 of 6 people found this instruction helpful.
  • Dale from Anderson, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Was this helpful?
Thank you for voting!
Loud Dryer
3 of 6 people found this instruction helpful.
  • Rod from YORBA LINDA, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Please do not buy parts from Parts Select. My order was not shipped the next day (as advertised on the web site), but instead 3 days later. I paid an extra couple of dollars for expedited shipping, which did made no difference (except for a couple of extra dollars for Parts Select to pocket).

When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.

I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service!
Was this helpful?
Thank you for voting!
dryer was making a grinding noise
2 of 3 people found this instruction helpful.
  • Scott from MUNCIE, IN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Was this helpful?
Thank you for voting!
would not heat
1 person found this instruction helpful.
  • Arthur from VALLEJO, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Was this helpful?
Thank you for voting!
All Instructions for the 11087402
121 - 135 of 354