11086402 Kenmore Dryer - Instructions

All Instructions for the 11086402
121 - 135 of 307

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer belt so old it slipped and would not turn drum
1 person found this instruction helpful.
  • Terry from TIVOLI, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver
Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke!
Another bonus is after 10 years I got to remove th e softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!
Was this helpful?
Thank you for voting!
Loud squeal noise when dryer running
1 person found this instruction helpful.
  • Joseph from Canonsburg, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.
Was this helpful?
Thank you for voting!
Drive belt puller broken
1 person found this instruction helpful.
  • James R from Atkins, AR
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Wrench (Adjustable)
Disassemble top and front of dryer removed drum. R2 pulley and belt. Cleaned and reassemble front door ops checked working order of machine . Replaced top. I thank you wife is happy.
Was this helpful?
Thank you for voting!
Noisy dryer and taking long to dry clothes
1 person found this instruction helpful.
  • Enrique from SAN DIEGO, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.
Was this helpful?
Thank you for voting!
Clothes would not dry
1 person found this instruction helpful.
  • John from WOODBRIDGE, VA
  • Easy
  • 1- 2 hours
  • Nutdriver
Unplug from electric ? outlet. Set the meter to ohm setting, check part ,no reading. Remove old part ,check new part with meter ,get a reading of 11 or more mA. Install new part and blower cover done.
Was this helpful?
Thank you for voting!
Idler pulley broke off.
1 person found this instruction helpful.
  • Edwin from PASADENA, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took back panel off, and it was really easy putting the new idler pulley in.
Was this helpful?
Thank you for voting!
pulley bad
1 person found this instruction helpful.
  • Dean from MAGNETIC SPGS, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
pull the back off and replace the pulley.
Was this helpful?
Thank you for voting!
Pulley wheel broke apart
1 person found this instruction helpful.
  • George from CLIFTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this helpful?
Thank you for voting!
Dryer would not start due to over heating
1 person found this instruction helpful.
  • John from HOPATCONG, NJ
  • Easy
  • 30 - 60 mins
  • Socket set
Followed the video.
Was this helpful?
Thank you for voting!
Squeaky tension pulley
1 person found this instruction helpful.
  • Trevor from Puyallup, WA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person found this instruction helpful.
  • Joe from St. Louis, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
dryer stopped and smelled of smoke.
2 of 4 people found this instruction helpful.
  • Jon from LaGrange, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Was this helpful?
Thank you for voting!
Loud hum but wouldn't work with a load in
2 of 4 people found this instruction helpful.
  • Ronald from Tulsa, OK
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.
Was this helpful?
Thank you for voting!
Dryer stopped heating
1 person found this instruction helpful.
  • Anna from Marietta, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding ea ch one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.
Was this helpful?
Thank you for voting!
The door whould not close enough for the dryer to work.
1 person found this instruction helpful.
  • Frank from Union Beach, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this helpful?
Thank you for voting!
All Instructions for the 11086402
121 - 135 of 307