11086402 Kenmore Dryer - Instructions

All Instructions for the 11086402
91 - 105 of 307

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Belt was raffling and there was aloud knocking sound
3 of 3 people found this instruction helpful.
  • Genette from CLEVELAND, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it
Was this helpful?
Thank you for voting!
Dryer was very loud and sounded like it was scraping
3 of 3 people found this instruction helpful.
  • Annde from JEFFERSON CTY, TN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people found this instruction helpful.
  • Thomas from KENT, CT
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people found this instruction helpful.
  • Steven from WICHITA, KS
  • Really Easy
  • 30 - 60 mins
  • Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
belt was cracking and dryer was somewhat noisy
4 of 7 people found this instruction helpful.
  • Melody from Silverton, CO
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Was this helpful?
Thank you for voting!
Dryer motor bearings failed. Motor wouldn't start.
8 of 19 people found this instruction helpful.
  • Mark from Maple Valley, WA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
electric dryer stopped heating - the thermostat got very hot
4 of 8 people found this instruction helpful.
  • Ignas from Midpines, CA
  • Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find whe re they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people found this instruction helpful.
  • Carl from MARION, KY
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
Dryer was making a loud squeaking noise
2 of 2 people found this instruction helpful.
  • James from Toccoa, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the video instructions. I took my time as this was a first for me. The disassembly was fairly straightforward. The belt idler pulley was definitely the problem as it wouldn’t turn at all. I decided to replace the support rollers also even though they seemed to be ok. Everything I had read said my model only needed 4 rollers bu t actually needed 6. I had to place a second order for those. Putting it all back together was fairly easy. Overall I had a good experience. Only a few tools were needed for this repair. Thank you,
Was this helpful?
Thank you for voting!
Idler Pulley squealing - Worn out
2 of 2 people found this instruction helpful.
  • Thomas E from PERRYSBURG, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.
Was this helpful?
Thank you for voting!
Belt Broken
2 of 2 people found this instruction helpful.
  • Gus from RIVERSIDE, CA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Watched video & took my time. It went easy
Was this helpful?
Thank you for voting!
All Instructions for the 11086402
91 - 105 of 307