11084422610 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no heat when drying clothes
My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.
Parts Used:
-
Tracey from Marion, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
lint filter full of holes and lint escaping
-
irvin from baltimore, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped heating
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Parts Used:
-
Joseph from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Stopped drying....little heat in drum but clothes not dried after 45 min.
Not knowing exactly what needed to be replaced I used the in-site questionnaire and followed through to problem and then ordered the first two items suggestions. Turned out the Heating Element Connection Wire Kit was redundant and not needed as the Cycling Thermostat included two such wire kits. I watched the video on the site and that gave me a fairly good idea how to proceed. I removed the back panel, lot of small screws, and then the Thermostat was easy to see. There are two similar looking parts but after closer look only one matched the new thermostat. Super easy, just remove wires and old thermostat and replace with new item and then before actually reinstalling back panel I put a load of damp clothes to dry. Half hour later...Wallaaa...problem resolved. Good luck with your fix. Oh, there is a sheet referencing to set the new thermostat if needed to a certain limit, however using old thermostat with its embedded model # found that factory setting for new one was fine. So, no need to reset.
Parts Used:
-
Jim from Simi Valley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The lint filter in the dyer of our stacked unit had a tear in it.
I simply removed the damaged lint filter and replaced it with the new one I purchased. It took less than 30 seconds to do.
Parts Used:
-
Judith from Renton, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
not enough heat to dry clothes
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Parts Used:
-
James C. from Cobbs Creek, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
-
Betty from Erie, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!