11084422610 Kenmore Dryer - Instructions

All Instructions for the 11084422610
1 - 15 of 102

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
lint filter screen was broken
63 of 72 people found this instruction helpful.
  • Kevin from Seattle, WA
  • Really Easy
  • Less than 15 mins
replace lint filter with new part. Great service and quick delivery! Thanks!
Was this helpful?
Thank you for voting!
Replacing worn drum support rollers and shafts.
60 of 69 people found this instruction helpful.
  • Gary from Canton, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.

Good luck, It s not as bad as it sounds.
Was this helpful?
Thank you for voting!
Temperature setting not working
19 of 23 people found this instruction helpful.
  • Robert from Buffalo, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people found this instruction helpful.
  • michael from indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Was this helpful?
Thank you for voting!
lint coming out duct outside
14 of 20 people found this instruction helpful.
  • john from hamlet, NC
  • Really Easy
  • Less than 15 mins
one of ears that holds filter was broken leaving a small gap so lint went into duct work so i replaced the cover and filter is now held in place letting the filter do its job trapping the lint
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people found this instruction helpful.
  • David from Fleetwood, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Was this helpful?
Thank you for voting!
No heat in dryer
10 of 14 people found this instruction helpful.
  • Noah from Maiden, NC
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Was this helpful?
Thank you for voting!
lint filter an cover was stolen by tenant
8 of 9 people found this instruction helpful.
  • Michael from WEST WARWICK, RI
  • Really Easy
  • Less than 15 mins
easy three prong push-in,...
Was this helpful?
Thank you for voting!
Loud rumble noise while drum was turning
9 of 12 people found this instruction helpful.
  • Marcia from CAmden, NY
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people found this instruction helpful.
  • Joseph from Austin, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people found this instruction helpful.
  • Betty from Erie, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
incessantly annoyingly squeaky dryer
5 of 6 people found this instruction helpful.
  • Douglas from Tiburon, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Was this helpful?
Thank you for voting!
lod and heat caused cracks
5 of 6 people found this instruction helpful.
  • Lawrence from Hull, MA
  • Really Easy
  • Less than 15 mins
replace basket with new one snapped in
Was this helpful?
Thank you for voting!
The dryer was squeaking and would not heat at all.
7 of 12 people found this instruction helpful.
  • Steven from Oxnard, CA
  • Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at f irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Was this helpful?
Thank you for voting!
Old filter and cover had rusted retaining clips and rusted out sections
4 of 4 people found this instruction helpful.
  • david from HAYWARD, CA
  • Very Easy
  • Less than 15 mins
Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!
Was this helpful?
Thank you for voting!
All Instructions for the 11084422610
1 - 15 of 102