11080 Kenmore - Instructions

All Instructions for the 11080
61 - 75 of 1934

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Upper agitator stopped moving
38 of 46 people found this instruction helpful.
  • Craig from Yadkinville, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ea rs were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.
Was this helpful?
Thank you for voting!
sounded out of balance even after shifting clothes
35 of 38 people found this instruction helpful.
  • Lori from Parchment, MI
  • Easy
  • 15 - 30 mins
  • Pliers
The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not wo rk properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.
Was this helpful?
Thank you for voting!
Machine would stop when finished rinse cycle and wouldn't spin or drain.
56 of 104 people found this instruction helpful.
  • Kenneth from El Paso, TX
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
I replaced the Lid Switch and the unit works fine. I also cleaned up some other issues in the unit which took about half the time.
Was this helpful?
Thank you for voting!
broken pump and burned out motor
39 of 53 people found this instruction helpful.
  • Anthony from Webster, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
The repair itself was very simply, probably largely due to the design of the machine which made getting to, and replacing the two faulty parts a cinch. Just unscrew the two screws on the motor brackets which hold the motor down, and remove the brackets. Then remove the two smaller brackets which hold the pump to the motor. Then remove the two clamps and hoses from the pump. Lastly disconnect the power supply from the motor and the pump and motor will then come out as one unit. Simply reverse the process when reinstalling the new pump and motor. I used a bit of oil to lubricate the new motor shaft but I am sure it probably isn't necessary. The job should take no more than half an hour tops.
Was this helpful?
Thank you for voting!
water leak at pump
35 of 41 people found this instruction helpful.
  • oscar from missouri city, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
1. remove 2 hoses at pump using pliers to open hose clamps and sliding them out of the way.
2. remove 2 retainers holding pump with screwdriver.
3. remove old pump and install new pump
4. clamp pump using retaining clips
5. re-connect hoses
Was this helpful?
Thank you for voting!
Washer filled v e r y slowly
33 of 36 people found this instruction helpful.
  • Jonathan from Arlington, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
I'd noticed for a while that our 15-year-old Kenmore washer was filling slowly, but when it started to take 30 minutes to fill to the "medium" level, I knew something was really wrong. There was plenty of water pressure, so I replaced a hose that was loaded with minerals and cleaned the filter (also clogged with minerals). But that didn' t help! So I ordered a new water inlet valve, and replaced that. There's nothing tricky about the repair -- the hardest part is opening and closing the washer, for which I found instructions online. (Even so, it's the most time-consuming part of the project.) The result is the washer now fills as fast as when it was new. Just for fun, I took apart the old valve and expected to find it encrusted with minerals, but it looked fine, so I'm not sure where the actual breakdown was. But since the part only cost $25 -- less than a service call, for sure -- I was very happy to use a half hour of my time and keep the machine going a while longer.
Was this helpful?
Thank you for voting!
The dryer would run i.e. the drum would turn, but there was no heat so the clothes didn’t dry.
33 of 38 people found this instruction helpful.
  • David from Joppa, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.
Was this helpful?
Thank you for voting!
dryer works but no heat.
35 of 44 people found this instruction helpful.
  • Tom from Grove, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Measured resistance on thermostats & heating element. Found thermostat open so ordered replacement part and heat again.
Was this helpful?
Thank you for voting!
Excessive tub wobble, tubs leaning forward of normal
31 of 33 people found this instruction helpful.
  • David from GLEN BURNIE, MD
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.

While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.

At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.

Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
Was this helpful?
Thank you for voting!
unbalanced load...knocking sound.
32 of 37 people found this instruction helpful.
  • Edward from Easthampton, MA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, sc rew). Reassembled washer then ran wash for a cycle. Successful fix.
Was this helpful?
Thank you for voting!
Found cracked brake shoe
33 of 41 people found this instruction helpful.
  • Michael from Trafalgar, IN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.
Was this helpful?
Thank you for voting!
Dryer had heat intermittently and would take 3 cycles to dry a load of clothes
35 of 48 people found this instruction helpful.
  • ANTHONY from MONROE, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are not sure what to replace. Oops, the first step is to unplug the dryer.
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people found this instruction helpful.
  • Bill from Houston, TX
  • Really Easy
  • Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people found this instruction helpful.
  • Grace from New Smyrna Beach, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
Top door catch assembly had broken
29 of 31 people found this instruction helpful.
  • tony from prineville, OR
  • Easy
  • Less than 15 mins
  • Screw drivers
It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!
Was this helpful?
Thank you for voting!
All Instructions for the 11080
61 - 75 of 1934