11080 Kenmore - Instructions

All Instructions for the 11080
76 - 90 of 1934

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would fill/empty but would not agitate nor spin
30 of 35 people found this instruction helpful.
  • Ted from SOUTH MILWAUKEE, WI
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The r ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people found this instruction helpful.
  • Robert from GOODRICH, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Was this helpful?
Thank you for voting!
Severe water leak
27 of 29 people found this instruction helpful.
  • Noel from Pollock, ID
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
Was this helpful?
Thank you for voting!
Dryer not spinning
33 of 49 people found this instruction helpful.
  • john from goldsboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Was this helpful?
Thank you for voting!
Drier would not heat
26 of 29 people found this instruction helpful.
  • Jason from Birmingham, AL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Wife said the drier was not heating. I looked on the internet and found Parts Select. Followed the instructions to test the heating element, thermal cut-offs, and thermostat. This is really easy, you just touch the terminals with the voltage meter to see which ones are not transmitting current (with the drier unplugged). One of the t hermal cut-offs was not transmitting current so I ordered the part Sunday night and had it by Wednesday morning and put it on it about five minutes. Steps:

1. Unplug drier
2. Unscrew back of drier
3. Unplug wires from terminals of the parts shown in Parts Select instructions (one at a time)
4. Get a basic voltage meter (I bought a cheap one at the big box store)
5. Test terminals (touch the red terminal on the voltage meter to one side, black to the other)
6. If the needle moves to the other side, the part is OK, if not order the part and replace.
Was this helpful?
Thank you for voting!
dryer ran but no heat
34 of 53 people found this instruction helpful.
  • Mary from Red Bud, IL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench set
I removed the dryer rear upper cover to expose the start and cycle selection knob. My wiring diagram was in there. I removed the wiring on the rear of the cycle selection knob (timer assembly) locations were marked on the device. I ohmed the switch contacts for the heat circuit and had an open circuit through out the full rotation of the knob. I removed the 2 screws on the back of the timer assembly and the burnt contacts fell out. I removed the knob and 2 mounting screws and the device was out to retrieve my part numbers.
Was this helpful?
Thank you for voting!
Dryer would not heat up; blow only air
26 of 30 people found this instruction helpful.
  • William from Sacramento, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver
I replaced the thermal cut off kit, and the dryer now had heat. Three days later, no heat; the thermal fuse also did not have continuity. Read on-line that overheating was the most likely cause. So, I checked the exhaust duct for blockage, but it was clear. Then, I removed the exhaust canister at the back of dryer; the entire bottom wa s filled with lint the size of a softball. The lint was heating up, and when it got too hot, it blew the thermal cut off. Cleaned out the lint, replaced the thermal cut off, and now it's fine. Moral of the story: Remove the lint canister and clean it.
Was this helpful?
Thank you for voting!
water overflowing when filling
34 of 54 people found this instruction helpful.
  • Marni from Buhl, ID
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly d ifferent configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!
Was this helpful?
Thank you for voting!
Water constantly dripped into washer when it was off.
24 of 25 people found this instruction helpful.
  • MARK from MARION, MA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people found this instruction helpful.
  • Jeff from Mesa, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people found this instruction helpful.
  • joe from cheswick, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
washer wouldnt agitate or spinn but would drain?
22 of 22 people found this instruction helpful.
  • lester from Belleville, WI
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people found this instruction helpful.
  • Roger from Palmyra, IN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Was this helpful?
Thank you for voting!
The dryer was running and it quit, just stopped. A friend looked at it and thought it was this switch. I purchased the switch and he installed and it still did not work.
24 of 28 people found this instruction helpful.
  • Debbie from Mooresville,, IN
  • Easy
  • Less than 15 mins
  • Nutdriver
No, if that had of been the problem, it would have worked. However, I called a service man out to look at it. It was a fuse that does not look like a fuse. I had the system already torn apart and cleaned. The service took a meter and checked the fuse ( that did not look like a fuse) and it was bad. It cost 14.00 for the fuse, it took less than 5 minutes for installation and the service fee was $65.00. My advise, get a meter, check everything yourself, and only purchase what you need.
Was this helpful?
Thank you for voting!
The spin gear was striped.
25 of 31 people found this instruction helpful.
  • Aaron from Lake Mills, WI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Socket set
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Was this helpful?
Thank you for voting!
All Instructions for the 11080
76 - 90 of 1934