- Home
- 11078490200
- Instructions
11078490200 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken belt
1 person
found this instruction helpful.
-
William from Newport, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine
... Read more
ss
Read less
Was this helpful?
Thank you for voting!
door would stay closed
1 person
found this instruction helpful.
-
william from KILLEEN, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person
found this instruction helpful.
-
Melody from TEXARKANA, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
Dryer was making a lot of noise while running.
3 of 7 people
found this instruction helpful.
-
Ramon from Los Angeles, CA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing t ... Read more he belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing t ... Read more he belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
Read less
Was this helpful?
Thank you for voting!
Dryer was making all kinds of noises
1 person
found this instruction helpful.
-
Noel from N BRANFORD, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and altho
... Read more
ugh not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Buzzing sound while start button pushed. then shut off after 30 seconds.
2 of 4 people
found this instruction helpful.
-
Brad from Lake City, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts
... Read more
at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person
found this instruction helpful.
-
Ava from BALTIMORE, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit
... Read more
-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Read less
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person
found this instruction helpful.
-
Scott from EVEREST, KS
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person
found this instruction helpful.
-
Lindsey from Lancaster, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the
... Read more
drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Read less
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people
found this instruction helpful.
-
satyavenkata from Bentonville, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
Noise in dryer when dryer was turned on
2 of 4 people
found this instruction helpful.
-
Michael from Marion, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,
Your great service is very hard to find.
Your great service is very hard to find.
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer stopped and smelled of smoke.
2 of 4 people
found this instruction helpful.
-
Jon from LaGrange, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be
... Read more
removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Read less
Was this helpful?
Thank you for voting!
Seal snapped, which lead to longer dry cycles.
2 of 4 people
found this instruction helpful.
-
Christian from Sunapee, NH
- Really Easy
- Less than 15 mins
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this helpful?
Thank you for voting!
catch was missing to close dryer door
2 of 4 people
found this instruction helpful.
-
DONNA from SAN LORENZO, CA
- Really Easy
- Less than 15 mins
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this helpful?
Thank you for voting!
door latch broke
1 person
found this instruction helpful.
-
Debra from Oakland, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out the old latch and replaced with a new one
Was this helpful?
Thank you for voting!