11078490200 Kenmore Dryer - Instructions

All Instructions for the 11078490200
121 - 135 of 320

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Machine would not start and light stayed on with door closed.
1 person found this instruction helpful.
  • Mark from TERREBONNE, OR
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Frank from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people found this instruction helpful.
  • john from el paso, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Was this helpful?
Thank you for voting!
Dryer door wouldn't shut
1 of 2 people found this instruction helpful.
  • Amy from Cumberland, RI
  • Really Easy
  • Less than 15 mins
The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.
Was this helpful?
Thank you for voting!
The male part of the door catch was broken
1 of 2 people found this instruction helpful.
  • David from Chhicago, IL
  • Really Easy
  • Less than 15 mins
Simply installed the piece and I was done. Took 10 seconds.
Was this helpful?
Thank you for voting!
Door latch snapped off.
1 of 2 people found this instruction helpful.
  • Karen from Randle, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.
Was this helpful?
Thank you for voting!
Broken door actuator spring -interposer for motor control
1 of 2 people found this instruction helpful.
  • Stephen from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
Was this helpful?
Thank you for voting!
Dryer door kept opening
1 of 2 people found this instruction helpful.
  • Jennifer from Big Timber, MT
  • Easy
  • Less than 15 mins
  • Screw drivers
Popped out the old door catch kit and replaced it with the new one! Easy!!
Was this helpful?
Thank you for voting!
The latch on my dryer door wasn't working. I was having to shove a towel in the door to get it to stay shut until I was able to repair it.
1 of 2 people found this instruction helpful.
  • Dan from Lockport, LA
  • Really Easy
  • Less than 15 mins
All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repai r guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!
Was this helpful?
Thank you for voting!
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
2 of 5 people found this instruction helpful.
  • Patrick from Ramsey, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Was this helpful?
Thank you for voting!
Dryer Door Wouldn't Shut
1 of 2 people found this instruction helpful.
  • Megan from Kettering, OH
  • Really Easy
  • Less than 15 mins
My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business a gain with partselect. Com if we ever need more parts.
Was this helpful?
Thank you for voting!
The dryer door catch wouldn't hold the door closed
1 of 2 people found this instruction helpful.
  • Gerald from Thompsonville, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this helpful?
Thank you for voting!
Door wouldn't fasten shut
1 of 2 people found this instruction helpful.
  • Susan from Laingsburg, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se rvice. You made my life easier.
Was this helpful?
Thank you for voting!
More Dry setting does not work
2 of 5 people found this instruction helpful.
  • c from vestavia hills, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Repair was not successful
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
All Instructions for the 11078490200
121 - 135 of 320