- Home
- 11078490200
- Instructions
11078490200 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud noise while in use
2 of 3 people
found this instruction helpful.
-
Josh from Madill, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people
found this instruction helpful.
-
Laszlo from Vienna, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
drum support roller was squeaking VERY loud
2 of 3 people
found this instruction helpful.
-
joe from southgate, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people
found this instruction helpful.
-
Charles from Cape Girardeau, MO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c
... Read more
lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Read less
Was this helpful?
Thank you for voting!
Worn bushing on bottom drum roller
3 of 6 people
found this instruction helpful.
-
Frank from Avon, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount
... Read more
ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer tumbler made a loud noise
2 of 3 people
found this instruction helpful.
-
jeff from albuquerque, NM
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people
found this instruction helpful.
-
Victoria from Roslyn Heights, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag
... Read more
ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Read less
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people
found this instruction helpful.
-
katherine from Salem, OR
- Easy
- 15 - 30 mins
-
Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw
... Read more
s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Read less
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person
found this instruction helpful.
-
Joe from St. Louis, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
1 person
found this instruction helpful.
-
Mark from BLOOMFIELD, CT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person
found this instruction helpful.
-
Steven from New Richmond, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You
... Read more
just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person
found this instruction helpful.
-
Jeff from OAKLAND, TN
- Really Easy
- 30 - 60 mins
-
Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
Loud hum but wouldn't work with a load in
2 of 4 people
found this instruction helpful.
-
Ronald from Tulsa, OK
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.
Was this helpful?
Thank you for voting!