11078490200 Kenmore Dryer - Instructions

All Instructions for the 11078490200
46 - 60 of 320

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
incessantly annoyingly squeaky dryer
5 of 6 people found this instruction helpful.
  • Douglas from Tiburon, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Was this helpful?
Thank you for voting!
Drum would not spin to drain water
9 of 18 people found this instruction helpful.
  • Gay from Apple Valley, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people found this instruction helpful.
  • Dillard C. from Vina, AL
  • Easy
  • 15 - 30 mins
  • Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people found this instruction helpful.
  • Anthony from PITTSTON, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people found this instruction helpful.
  • james from york, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Gasket was falling off, needed replacement
4 of 6 people found this instruction helpful.
  • Anthony from N. Ferrisburg, VT
  • Really Easy
  • Less than 15 mins
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this helpful?
Thank you for voting!
a broken belt
6 of 12 people found this instruction helpful.
  • Dorise from Donalsonville, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
my hany man did it....
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
All Instructions for the 11078490200
46 - 60 of 320