- Home
- 11076002011
- Instructions
11076002011 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lint filter seal worn out
5 of 5 people
found this instruction helpful.
-
Dennis from PALM BCH GDNS, FL
- Very Easy
- Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
Dryer stopping during dry cycle.
8 of 14 people
found this instruction helpful.
-
James from HARTSELLE, AL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to remo
... Read more
ved the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old lint filter was broken
8 of 14 people
found this instruction helpful.
-
Earl from Santa Ana, CA
- Really Easy
- Less than 15 mins
Just replaced the old lint filter.
Was this helpful?
Thank you for voting!
Broken Drum Belt
4 of 4 people
found this instruction helpful.
-
Garry from Garland, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Just like the video, just followed the video
Thanks,
Thanks,
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people
found this instruction helpful.
-
Charles from Long Beach, CA
- Easy
- 30 - 60 mins
-
Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!
Unit not spent
4 of 4 people
found this instruction helpful.
-
Boonkham from SMYRNA, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Just replaced part
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people
found this instruction helpful.
-
Paul from STONE CREEK, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Idler pulley destroyed
6 of 10 people
found this instruction helpful.
-
Jack from NORTHFIELD, OH
- Very Easy
- 30 - 60 mins
Per instruction video and past experience. Part replacement came quickly (2days from purchase) and the correct parts were sent. Dryer works better now than it did new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people
found this instruction helpful.
-
Kevin from VALDOSTA, GA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Dryer too hot
4 of 4 people
found this instruction helpful.
-
ALAN from MIDLOTHIAN, VA
- Very Easy
- 15 - 30 mins
-
Screw drivers
I replaced both the thermal fuse and the thermistor at the same time. That seemed to fix the problem; but after a couple of days the dryer would not start. When pushing the Hold to Start button, the dryer just gave one beep and would not start. I did a resistance test on the old thermal fuse, and it was OK; so I put the old thermal fus
... Read more
e back in and the dryer works. Evidently, it was just the thermistor (thermostat, internal bias) that was broken. Both are very easy to change.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
LP conversion kit
8 of 17 people
found this instruction helpful.
-
Steve from Brunswick, VT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate m
... Read more
y snap ring pliers(just moved). The directions were spot on, read them through once before you start.
Read less
Was this helpful?
Thank you for voting!
No Gas Heat
4 of 5 people
found this instruction helpful.
-
Debra from Springfield, PA
- Very Difficult
- More than 2 hours
-
Nutdriver
I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together t
... Read more
o save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!
Read less
Was this helpful?
Thank you for voting!
The dryer would not heat up
4 of 5 people
found this instruction helpful.
-
William from Canyon Country, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...
Was this helpful?
Thank you for voting!
Whirlpool Gas dryer, run but no heat
4 of 5 people
found this instruction helpful.
-
Fred from Macomb, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air
... Read more
and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F
Read less
Was this helpful?
Thank you for voting!