- Home
- 11076002011
- Instructions
11076002011 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light won’t come on when dryer door is opened & drum won’t stop when door is opened
3 of 3 people
found this instruction helpful.
-
John from LINDALE, GA
- Very Easy
- Less than 15 mins
-
Screw drivers
Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top
... Read more
front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.
Read less
Was this helpful?
Thank you for voting!
A hole in filter
3 of 3 people
found this instruction helpful.
-
Russ from Vernal, UT
- Really Easy
- Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
Dryer would not start!
5 of 9 people
found this instruction helpful.
-
Manny from ODESSA, TX
- Really Easy
- Less than 15 mins
-
Socket set
Unplug unit first.
Took the front cover off the front of dryer below the door.
Took the front cover off the front of dryer below the door.
Was this helpful?
Thank you for voting!
dryer would not work .
3 of 3 people
found this instruction helpful.
-
Tom from MEARS, MI
- Really Easy
- 15 - 30 mins
-
Socket set
Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
3 of 3 people
found this instruction helpful.
-
Lawrence from ARITON, AL
- A Bit Difficult
- More than 2 hours
-
Screw drivers, Socket set
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to
... Read more
be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
Read less
Was this helpful?
Thank you for voting!
Making a racket.
3 of 3 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this helpful?
Thank you for voting!
dryer wasnt heating up, though it would run
3 of 3 people
found this instruction helpful.
-
Chris from st louis, MO
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply.
... Read more
New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.
Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!
Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!
Read less
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people
found this instruction helpful.
-
Thomas from TULELAKE, CA
- Very Difficult
- 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
Read less
Was this helpful?
Thank you for voting!
My dryer would not heat. Drum was spinning fine and everything else was working just no heat.
5 of 9 people
found this instruction helpful.
-
Lance from RCH CUCAMONGA, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.
Was this helpful?
Thank you for voting!
dryer did not run
3 of 3 people
found this instruction helpful.
-
Gerald from STATE COLLEGE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
remove top, front, drum, fan fan housing, replace motor
Was this helpful?
Thank you for voting!
Dryer would squeal when the drum was turning
3 of 3 people
found this instruction helpful.
-
Clinton from MINOOKA, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace t
... Read more
hem all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start
3 of 3 people
found this instruction helpful.
-
Diane from BEVERLY HILLS, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Part came in about 3 days. After reading and checking what was wrong with the Dryer -- which i read if there was no noise coming from the dryer it was the door switch, Looked up the part number and then saw a video that showed how to install the door switch. The video was so informative and precise on everything you had to do and easy
... Read more
Saved money on a service call.
Read less
Was this helpful?
Thank you for voting!
YouTube video dated 9/28/2015
3 of 3 people
found this instruction helpful.
-
Madeline from PANA, IL
- Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this helpful?
Thank you for voting!
Squeaky dryer
3 of 3 people
found this instruction helpful.
-
robert from ELMA, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ezee pezee lemon squeezee.
Was this helpful?
Thank you for voting!