110716 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The switch was not working so got a new switch
3 of 7 people
found this instruction helpful.
-
satyavenkata from Bentonville, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
replace idler pully
1 person
found this instruction helpful.
-
curtis from STOCKBRIDGE, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug
... Read more
connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person
found this instruction helpful.
-
Joe from St. Louis, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
would not heat
1 person
found this instruction helpful.
-
Arthur from VALLEJO, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Was this helpful?
Thank you for voting!
Idler pulley broke off.
1 person
found this instruction helpful.
-
Edwin from PASADENA, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took back panel off, and it was really easy putting the new idler pulley in.
Was this helpful?
Thank you for voting!
pulley bad
1 person
found this instruction helpful.
-
Dean from MAGNETIC SPGS, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
pull the back off and replace the pulley.
Was this helpful?
Thank you for voting!
Pulley wheel broke apart
1 person
found this instruction helpful.
-
George from CLIFTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this helpful?
Thank you for voting!
Squeaky tension pulley
1 person
found this instruction helpful.
-
Trevor from Puyallup, WA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than
... Read more
the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat.
1 person
found this instruction helpful.
-
Jon from WILLIAMSBURG, MA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Socket set
The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling
... Read more
with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.
Read less
Was this helpful?
Thank you for voting!
F-26 Fault message
1 person
found this instruction helpful.
-
DW from ALVIN, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people
found this instruction helpful.
-
Enrique from Miami Shores, FL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w
... Read more
asher door bang shut.Took longer than expected, but each procedure was simple.
Read less
Was this helpful?
Thank you for voting!
Dryer Drum Would Not Rotate
1 of 2 people
found this instruction helpful.
-
Russ from MARIETTA, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 year
... Read more
s old. Running great now. Thank You!
Read less
Was this helpful?
Thank you for voting!
Dryer would not light
1 of 2 people
found this instruction helpful.
-
Charles from MT PROSPECT, IL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame
... Read more
sensor and no gas smell for 2 weeks now.
Read less
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people
found this instruction helpful.
-
Rick from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!