110716 Kenmore - Instructions

All Instructions for the 110716
91 - 105 of 215

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Coin op Whirpool Dryer Broken drive belt and frozen drum wheels
3 of 3 people found this instruction helpful.
  • Kevin from LEMOORE, CA
  • Really Easy
  • 30 - 60 mins
Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed fro nt panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)
Was this helpful?
Thank you for voting!
Bad screaming noise
3 of 3 people found this instruction helpful.
  • David from HUNTINGDON VY, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Replaced 4 wheels and new belt
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people found this instruction helpful.
  • Steven from WICHITA, KS
  • Really Easy
  • 30 - 60 mins
  • Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
Dryer was not running as fast as normal, belt was squeaking loudly
3 of 4 people found this instruction helpful.
  • Victor from ORANGE, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.
Was this helpful?
Thank you for voting!
Dryer won't start.Only make a click noise.
3 of 4 people found this instruction helpful.
  • Candido from GREENVILLE, TX
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this helpful?
Thank you for voting!
Door switch would not let dryer operate
2 of 2 people found this instruction helpful.
  • George from Rio Communities, NM
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top bac k out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Was this helpful?
Thank you for voting!
No leveling feet on dryer.
2 of 2 people found this instruction helpful.
  • Bobbie from BEND, OR
  • Very Easy
  • Less than 15 mins
  • Wrench (Adjustable)
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this helpful?
Thank you for voting!
Very loud squeaking!
2 of 2 people found this instruction helpful.
  • Travis from GARRETT, IN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
Was this helpful?
Thank you for voting!
Repair video made it easy
2 of 2 people found this instruction helpful.
  • Jack from DINUBA, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Just follow the repair video, it was easy!
Was this helpful?
Thank you for voting!
Shutting off and had to wait before could turn back on
2 of 2 people found this instruction helpful.
  • Allen from KENNETT, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Followed online video very easy and dryer works like new one....
Was this helpful?
Thank you for voting!
Part broken in half
3 of 5 people found this instruction helpful.
  • Sean from ROCK HILL, SC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
Was this helpful?
Thank you for voting!
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
2 of 2 people found this instruction helpful.
  • Steven from CAMARILLO, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people found this instruction helpful.
  • Carl from MARION, KY
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
Dryer was making a loud squeaking noise
2 of 2 people found this instruction helpful.
  • James from Toccoa, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the video instructions. I took my time as this was a first for me. The disassembly was fairly straightforward. The belt idler pulley was definitely the problem as it wouldn’t turn at all. I decided to replace the support rollers also even though they seemed to be ok. Everything I had read said my model only needed 4 rollers bu t actually needed 6. I had to place a second order for those. Putting it all back together was fairly easy. Overall I had a good experience. Only a few tools were needed for this repair. Thank you,
Was this helpful?
Thank you for voting!
the fastener became loose and dropped into the stove
2 of 3 people found this instruction helpful.
  • George E from OCALA, FL
  • Really Easy
  • 30 - 60 mins
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
Was this helpful?
Thank you for voting!
All Instructions for the 110716
91 - 105 of 215