110716 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer was making a grinding noise
2 of 3 people
found this instruction helpful.
-
Scott from MUNCIE, IN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the
... Read more
pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Read less
Was this helpful?
Thank you for voting!
Dryer kept throwing the E1 error indicating the thermistor needed replacement
2 of 3 people
found this instruction helpful.
-
Rory from LEESBURG, VA
- Easy
- 15 - 30 mins
-
Socket set
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back i
... Read more
n, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Read less
Was this helpful?
Thank you for voting!
It was the heat safety switch in the old drive motor
2 of 3 people
found this instruction helpful.
-
Andrew from HATTIESBURG, MS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people
found this instruction helpful.
-
Victoria from Roslyn Heights, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag
... Read more
ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Read less
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people
found this instruction helpful.
-
James from Richmond, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
machine wouldn't turn on when lid closed
2 of 3 people
found this instruction helpful.
-
Ellen from NYACK, NY
- Easy
- Less than 15 mins
-
Screw drivers
replaced missing screw and pad and now machine works perfectly
Other Parts Used:
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
Just got new dryer so I wanted metal duct to help keep lint from building up in duct
1 person
found this instruction helpful.
-
Joseph from MEMPHIS, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Pulled dryer out from the wall and measured the distance between dryer and outlet and made the necessary cuts to proper length then installed it , moved dryer back into place . ready for clothes and no duct problems.
Was this helpful?
Thank you for voting!
Loud scratching noise, very loud
1 person
found this instruction helpful.
-
Mark from Linthicum Heights, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and r ... Read more emoved old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and r ... Read more emoved old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Read less
Was this helpful?
Thank you for voting!
Loud squealing noise during operation
1 person
found this instruction helpful.
-
gerald from LEBANON, PA
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulle ... Read more y lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulle ... Read more y lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Read less
Was this helpful?
Thank you for voting!
would ignite but not run for more than 10 min.
2 of 4 people
found this instruction helpful.
-
brian from butte, MT
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it
... Read more
turned on and ran replaced cover and done.
Read less
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Loud squeal noise when dryer running
1 person
found this instruction helpful.
-
Joseph from Canonsburg, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.
Was this helpful?
Thank you for voting!
The dryer would shut off mid-cycle.
1 person
found this instruction helpful.
-
Michael from ONEONTA, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dry
... Read more
er works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Read less
Was this helpful?
Thank you for voting!
Broken grill
1 person
found this instruction helpful.
-
Barbara from WIMAUMA, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
With the instructional video the repair was very easy.
Was this helpful?
Thank you for voting!