1106809 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Quick Boil burner would not stay heated and did not reach the required temperature.
2 of 2 people
found this instruction helpful.
-
Ronald from NOVI, MI
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
The repair was easy. Shut off all power to the range, or unplug it. Remove the sheet metal back from the control panel using a nut driver or socket set. Pull the knob from the front of the control panel. Remove the two Phillips head screws that were hidden behind the knob. Pull the control switch out the back side of the control pan
... Read more
el. Compare the old switch with the new one, to make absolutely sure you have the correct switch. Remove one wire at a time from the old switch and immediately install it in the exact same position on the new switch. When you have successfully transferred all of the wires from the old switch to the new switch, reinstall the new switch using the two Phillips screws. Reinstall the knob and the sheet metal cover. Plug the range back in, and/or turn the power back on. Trying boiling a pan of water to confirm that the repair resolved the issue.
Read less
Was this helpful?
Thank you for voting!
No leveling feet on dryer.
2 of 2 people
found this instruction helpful.
-
Bobbie from BEND, OR
- Very Easy
- Less than 15 mins
-
Wrench (Adjustable)
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t ... Read more he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t ... Read more he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Read less
Was this helpful?
Thank you for voting!
Door switch had failed. Dryer would not start.
3 of 5 people
found this instruction helpful.
-
dan from Melbourne, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Opened front of dryer and replaced switch.
Best part was ordering and receiving switch in two days. You guys really do ship the same day as ordered.
Best part was ordering and receiving switch in two days. You guys really do ship the same day as ordered.
Was this helpful?
Thank you for voting!
Door switch would not let dryer operate
2 of 2 people
found this instruction helpful.
-
George from Rio Communities, NM
- Very Easy
- Less than 15 mins
-
Screw drivers
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top bac
... Read more
k out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Read less
Was this helpful?
Thank you for voting!
lint screen was not catching lint and sending out the dryer vent
2 of 2 people
found this instruction helpful.
-
Scott from WOODBURY, MN
- Very Easy
- Less than 15 mins
replaced dryer lint screen with new.
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people
found this instruction helpful.
-
Susan from WARREN, NJ
- Very Easy
- Less than 15 mins
-
Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
The Dryer door catch broke and the door would not latch.
2 of 2 people
found this instruction helpful.
-
Douglas from LINCOLN, NE
- Really Easy
- Less than 15 mins
-
Pliers
I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.
Was this helpful?
Thank you for voting!
Dryer electrically dead
3 of 6 people
found this instruction helpful.
-
Dale from Anderson, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Was this helpful?
Thank you for voting!
The lint filter needed replacement due to what is probably normal wear and tear.
2 of 3 people
found this instruction helpful.
-
Donna from CARY, NC
- Very Easy
- Less than 15 mins
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this helpful?
Thank you for voting!
Screen ripped
2 of 3 people
found this instruction helpful.
-
Cindy from BENZONIA, MI
- Very Easy
- Less than 15 mins
Dropped new filter in.
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people
found this instruction helpful.
-
Victoria from Roslyn Heights, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag
... Read more
ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Read less
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people
found this instruction helpful.
-
James from Richmond, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people
found this instruction helpful.
-
Laszlo from Vienna, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
Dryer kept throwing the E1 error indicating the thermistor needed replacement
2 of 3 people
found this instruction helpful.
-
Rory from LEESBURG, VA
- Easy
- 15 - 30 mins
-
Socket set
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back i
... Read more
n, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Read less
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people
found this instruction helpful.
-
katherine from Salem, OR
- Easy
- 15 - 30 mins
-
Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw
... Read more
s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Read less
Was this helpful?
Thank you for voting!