1106809 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A hole in filter
3 of 3 people
found this instruction helpful.
-
Russ from Vernal, UT
- Really Easy
- Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
Door Latch Broken
3 of 3 people
found this instruction helpful.
-
James from Oceanside, CA
- Very Easy
- Less than 15 mins
Ordered new latch. Installed new latch into the dryer within one minute.
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people
found this instruction helpful.
-
james from york, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people
found this instruction helpful.
-
Thomas from TULELAKE, CA
- Very Difficult
- 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
Read less
Was this helpful?
Thank you for voting!
YouTube video dated 9/28/2015
3 of 3 people
found this instruction helpful.
-
Madeline from PANA, IL
- Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this helpful?
Thank you for voting!
Clothes were not drying on auto sensor.
3 of 3 people
found this instruction helpful.
-
Michael from Annapolis, MD
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this helpful?
Thank you for voting!
not drying completely on the automatic settings
3 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Easy
- Less than 15 mins
-
Pliers
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen.
... Read more
Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Read less
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people
found this instruction helpful.
-
donald from MANVILLE, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people
found this instruction helpful.
-
Mark from Clarksburg, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R
... Read more
einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Blower motor control board failure
3 of 4 people
found this instruction helpful.
-
Tracy from Cedar Park, TX
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Once I was able to diagnose the failure (F-44 error, happened multiple times per load), the only thing I had to do was 1) Remove the 3 screws in the back of the control panel 2) Locate the blower motor controller (facing the front of the dryer it is the smaller control board on the far left) 3) remove the wire-harnesses from the control b
... Read more
oard 4) remove the 2 nuts with socket and 5) put new board in. Took me about 10 minutes from start to finish.
Read less
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people
found this instruction helpful.
-
Ed from Charlottesville, VA
- Easy
- Less than 15 mins
-
Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen
... Read more
t, and other parts. At some point it will be time for a new dryer...
Read less
Was this helpful?
Thank you for voting!
Dryer won't start.Only make a click noise.
3 of 4 people
found this instruction helpful.
-
Candido from GREENVILLE, TX
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this helpful?
Thank you for voting!