1106809 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bulb worked for a couple days and has now burned out, filaments dangling
3 of 4 people
found this instruction helpful.
-
Amy from JUNCTION, TX
- Easy
- Less than 15 mins
-
Screw drivers
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.
I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people
found this instruction helpful.
-
Wayne from Rosenberg, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate
... Read more
d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Read less
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people
found this instruction helpful.
-
Cynthia M from Westfield, MA
- Easy
- More than 2 hours
-
Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too
... Read more
shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Read less
Was this helpful?
Thank you for voting!
Dryer stopped heating
3 of 4 people
found this instruction helpful.
-
Linda from DANVILLE, CA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
We have a very early model of the He3. We had to follow directions for the He2 model to replace the heater element and thermostat. Access is easy through the front panel, but removing and replacing the element required some force and maneuvering in a small area.
We replaced both the element and the thermostat since we had the ... Read more entire part disconnected and removed. So far working great!
We replaced both the element and the thermostat since we had the ... Read more entire part disconnected and removed. So far working great!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer won’t start
3 of 4 people
found this instruction helpful.
-
Kyle from HANOVER, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people
found this instruction helpful.
-
Steven from WICHITA, KS
- Really Easy
- 30 - 60 mins
-
Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
Shutting off and had to wait before could turn back on
2 of 2 people
found this instruction helpful.
-
Allen from KENNETT, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Followed online video very easy and dryer works like new one....
Was this helpful?
Thank you for voting!
Lights turn on, all the beeps but dryer won't start.
2 of 2 people
found this instruction helpful.
-
James from HONESDALE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the wrong part. It was pick and choose from the info provided.I checked again and found one that's 58% of the time the part.
Was this helpful?
Thank you for voting!
Heater element had burnt open and would not heat.
2 of 2 people
found this instruction helpful.
-
Joe from COWARD, SC
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overl
... Read more
oad. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.
Read less
Was this helpful?
Thank you for voting!
Broken dryer belt and broken idler pulley wheel
3 of 5 people
found this instruction helpful.
-
ROGER from MADISON, TN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Looked it up on YouTube and followed the video instructions. Repair went fine after I got the correct parts ordered from two different places before I got the correct parts. Parts Select was the only one that sent the correct parts.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer not heating
2 of 2 people
found this instruction helpful.
-
James from GREENVILLE, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver
Confirmed I had incoming 240V, checked continuity on element switch confirmed bad. Ordered replacement part. U have to remove drum to replace element
Was this helpful?
Thank you for voting!
Dryer wouldn't Heat up. Otherwise all else worked
2 of 2 people
found this instruction helpful.
-
Paul from BIGFORK, MT
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Thought I could do it myself. Bought most parts recommended by this site
Took backoff thinking I could get to heating element. Noticed I would have to take out drum. Being in my 90's, decided to call repairman. He came and replaced the heating element I had purchased. He didn't have to come back
after he had purchased parts. ... Read more That saved about half my bill. Worked Great!
Took backoff thinking I could get to heating element. Noticed I would have to take out drum. Being in my 90's, decided to call repairman. He came and replaced the heating element I had purchased. He didn't have to come back
after he had purchased parts. ... Read more That saved about half my bill. Worked Great!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Electric Heating Element went out.
2 of 2 people
found this instruction helpful.
-
John from WELLS, MN
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
I checked continuity of all electrical points. I took the top off, then the back, and front of the dryer off so it was easy to inspect the whole dryer. I was also able to clean unwanted dust, and lent with a shop vacuum by doing this.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking ... Read more pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking ... Read more pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
Read less
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
The door catch no longer held the door shut. It would not grip the bayonet.
2 of 2 people
found this instruction helpful.
-
Douglass from Madison, IN
- Very Easy
- Less than 15 mins
-
Pliers
The only challenging part was getting the old catch out. It can easily fall inside the door, not that this is really a problem, just leave it there. Using pliers get a good grip on the edge of the old catch and rock the top out, then pull to get the bottom out. There will now be an open hole. Align the new part with the open hole, and sim
... Read more
ply push it in. It will catch, and click into place. No tools are needed to install.
Read less
Was this helpful?
Thank you for voting!