- Home
- 1106617821
- Instructions
1106617821 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum rear seal bad
1 person
found this instruction helpful.
-
Ron from COAL CITY, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
Was this helpful?
Thank you for voting!
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
1 person
found this instruction helpful.
-
Charles from Rupert, ID
- Really Easy
- 30 - 60 mins
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the dis
... Read more
charges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Read less
Was this helpful?
Thank you for voting!
Buzzing sound while start button pushed. then shut off after 30 seconds.
2 of 4 people
found this instruction helpful.
-
Brad from Lake City, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts
... Read more
at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer stopped and smelled of smoke.
2 of 4 people
found this instruction helpful.
-
Jon from LaGrange, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be
... Read more
removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Read less
Was this helpful?
Thank you for voting!
Dryer was making a lot of noise while running.
3 of 7 people
found this instruction helpful.
-
Ramon from Los Angeles, CA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing t ... Read more he belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing t ... Read more he belt from the motor pulley and tensioner, and then pulling the drum straight out.
At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.
Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.
(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
Read less
Was this helpful?
Thank you for voting!
Dryer was making all kinds of noises
1 person
found this instruction helpful.
-
Noel from N BRANFORD, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and altho
... Read more
ugh not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person
found this instruction helpful.
-
j from TAZEWELL, TN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person
found this instruction helpful.
-
Tammy from glenford, OH
- Very Easy
- Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
Dryer door would not stay closed
1 person
found this instruction helpful.
-
Gregg from St. Augustine, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this helpful?
Thank you for voting!
Old filter handle broke
1 person
found this instruction helpful.
-
ronald from PICKENS, WV
- Really Easy
- Less than 15 mins
replaced filter
Was this helpful?
Thank you for voting!
Handle on lint filter cracked and came apart
1 person
found this instruction helpful.
-
ROSEMARIE*SALVO from BRONX, NY
- Very Easy
- Less than 15 mins
Opebed lint filter door, removed old lint filter and replaced it with new one.
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Susan from HUDSON, MA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Dryer drum wasn't turning
1 person
found this instruction helpful.
-
Carrie from PLAINFIELD, IL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person
found this instruction helpful.
-
Barbara from NORTH EASTON, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person
found this instruction helpful.
-
Kenneth from UPPR MARLBORO, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!