1106617821 Kenmore Dryer - Instructions

All Instructions for the 1106617821
76 - 90 of 309

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer tumbler made a loud noise
2 of 3 people found this instruction helpful.
  • jeff from albuquerque, NM
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
Fan blade had to be removed , was broken off from motor.
2 of 3 people found this instruction helpful.
  • James from Colorado Springs, CO
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people found this instruction helpful.
  • Charles from Cape Girardeau, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Was this helpful?
Thank you for voting!
Blower flywheel needed replacement
2 of 3 people found this instruction helpful.
  • Gary from SAINT LOUIS, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ning around the house looking for the model number of the dryer.
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people found this instruction helpful.
  • katherine from Salem, OR
  • Easy
  • 15 - 30 mins
  • Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people found this instruction helpful.
  • Laszlo from Vienna, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people found this instruction helpful.
  • Josh from Madill, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person found this instruction helpful.
  • Melody from TEXARKANA, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
broken belt
1 person found this instruction helpful.
  • William from Newport, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine ss
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person found this instruction helpful.
  • Lindsey from Lancaster, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person found this instruction helpful.
  • Ava from BALTIMORE, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit -which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person found this instruction helpful.
  • Scott from EVEREST, KS
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person found this instruction helpful.
  • Jeff from OAKLAND, TN
  • Really Easy
  • 30 - 60 mins
  • Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person found this instruction helpful.
  • Steven from New Richmond, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this helpful?
Thank you for voting!
All Instructions for the 1106617821
76 - 90 of 309