1106617821 Kenmore Dryer - Instructions

All Instructions for the 1106617821
46 - 60 of 309

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer wouldn’t drain and spin
3 of 3 people found this instruction helpful.
  • Thomas from KENT, CT
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Was this helpful?
Thank you for voting!
Original lint filter had broken handle
3 of 3 people found this instruction helpful.
  • steven from Buffalo, NY
  • Very Easy
  • Less than 15 mins
Ordered a correct part # lint filter from this site, removed old filter & installed the new, very simple fix.
Was this helpful?
Thank you for voting!
Broken lint filter
3 of 3 people found this instruction helpful.
  • Miriam from BRUNSWICK, OH
  • Very Easy
  • Less than 15 mins
Opened new package took item out and put it on the slot where the old filter was. Easy as pie. My dryer is 46 years old and works just fine.
Was this helpful?
Thank you for voting!
the dryer would not turn on
4 of 6 people found this instruction helpful.
  • Warren from PHILADELPHIA, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The first step was to check the electrical supply to make sure I had power 120 volt. I unplugged the dryer and turned off the gas supply and turned the dryer around so I could have access to the back panel removed panel to access the wiring harness and safety thermostats. All switches and wire checked good with my ohmmeter .I pulled off t he front kick panel and checked the electrical schematic and found the door switch was in the circuit to check it I had to lift up the top and pop out the front to access the door switch checked switch and found it defective. Replaced switch vacuumed out dryer and vent reassembled dryer and all worked good.
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people found this instruction helpful.
  • PHILLIP from AUSTIN, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people found this instruction helpful.
  • Vern from NEWBERG, OR
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
Mother was frozen up
3 of 3 people found this instruction helpful.
  • Dan from SYRACUSE, UT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I followed the video. So easy..
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people found this instruction helpful.
  • Rodney from Mt. Jackson, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people found this instruction helpful.
  • Russell from Apache Junction, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people found this instruction helpful.
  • Mark from Clarksburg, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people found this instruction helpful.
  • Ed from Charlottesville, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen t, and other parts. At some point it will be time for a new dryer...
Was this helpful?
Thank you for voting!
All Instructions for the 1106617821
46 - 60 of 309