1106507821 Kenmore Dryer - Instructions

All Instructions for the 1106507821
121 - 135 of 397

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Blower flywheel needed replacement
2 of 3 people found this instruction helpful.
  • Gary from SAINT LOUIS, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ning around the house looking for the model number of the dryer.
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person found this instruction helpful.
  • Jeff from OAKLAND, TN
  • Really Easy
  • 30 - 60 mins
  • Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person found this instruction helpful.
  • Steven from New Richmond, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person found this instruction helpful.
  • Joe from St. Louis, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
1 person found this instruction helpful.
  • Charles from Rupert, ID
  • Really Easy
  • 30 - 60 mins
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the dis charges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this helpful?
Thank you for voting!
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
1 person found this instruction helpful.
  • Thomas from LINCOLN, NE
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this helpful?
Thank you for voting!
The door cables broke.
1 person found this instruction helpful.
  • Robert from Perris, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I replaced the springs and cables in the dryer door.
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person found this instruction helpful.
  • Melody from TEXARKANA, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
broken belt
1 person found this instruction helpful.
  • William from Newport, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine ss
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Noise in dryer when dryer was turned on
2 of 4 people found this instruction helpful.
  • Michael from Marion, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.
Was this helpful?
Thank you for voting!
Drum rear seal bad
1 person found this instruction helpful.
  • Ron from COAL CITY, IL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person found this instruction helpful.
  • Lindsey from Lancaster, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this helpful?
Thank you for voting!
would not heat
1 person found this instruction helpful.
  • Arthur from VALLEJO, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person found this instruction helpful.
  • Ava from BALTIMORE, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit -which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this helpful?
Thank you for voting!
All Instructions for the 1106507821
121 - 135 of 397