1106507821 Kenmore Dryer - Instructions

All Instructions for the 1106507821
91 - 105 of 397

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer made loud rumbling noise and then shut down
4 of 7 people found this instruction helpful.
  • John from Wilton, CA
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
It had been making noise for a week and I bought the two drum support rollers hoping that was the problem. It wasn't as the dryer started shutting down after a few minutes of running. I opened the top of the dryer and removed the 2 screws holding the face and door on. I removed the face and disconnected the door switch wires and released the drum belt by pushing on the idler pully. I then removed the drum straight out the top. I then put a wrench on the fan on the back of the motor and unscrewed it and then released the two holdown clamps on the motor and removed the motor. I had to make a couple of wiring modifications for the new motor but the instructions and connectors that came with the motor were perfect. I put everything back together and plugged the dryer back in and tried to start it and .... Nothing. I forgot to reconnect the door switch wires. Fixed that and the dryer now runs as good as new and makes no noise at all now (almost anyway). It should be good for another 10 years easy.
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people found this instruction helpful.
  • Wayne from Rosenberg, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people found this instruction helpful.
  • Russell from Apache Junction, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Was this helpful?
Thank you for voting!
Dryer heating up but clothes not drying
3 of 4 people found this instruction helpful.
  • Donald from Knoxville, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.
Was this helpful?
Thank you for voting!
chute wore out
3 of 4 people found this instruction helpful.
  • Robert from MACON, GA
  • Very Difficult
  • 30 - 60 mins
I never received my part checked back after said hearing part had been shipped was told part was no longer available have called twice about my refund and not received that either
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people found this instruction helpful.
  • Mark from Clarksburg, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people found this instruction helpful.
  • Raymond from Washington, DC
  • Really Easy
  • Less than 15 mins
  • Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people found this instruction helpful.
  • Ed from Charlottesville, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen t, and other parts. At some point it will be time for a new dryer...
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people found this instruction helpful.
  • Susan from WARREN, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
screen worn out
2 of 2 people found this instruction helpful.
  • Elaine from CENTEREACH, NY
  • Very Easy
  • Less than 15 mins
re-placed screen
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
broken door cables
2 of 2 people found this instruction helpful.
  • Richard from LA BELLE, PA
  • Really Easy
  • 30 - 60 mins
followed directions that came with order confirmation e-mail
Was this helpful?
Thank you for voting!
Noisy while in use.
2 of 2 people found this instruction helpful.
  • Charles from ERIE, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
Was this helpful?
Thank you for voting!
Dryer was making a loud sound
2 of 2 people found this instruction helpful.
  • Frans from N ARLINGTON, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
Was this helpful?
Thank you for voting!
All Instructions for the 1106507821
91 - 105 of 397