1106507821 Kenmore Dryer - Instructions

All Instructions for the 1106507821
106 - 120 of 397

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
one of my rollers fell to pieces
2 of 2 people found this instruction helpful.
  • james from Fredericksburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Was this helpful?
Thank you for voting!
Dryer stopped working.
3 of 5 people found this instruction helpful.
  • Andrew from Edina, MN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.
Was this helpful?
Thank you for voting!
The original motor stopped working
2 of 2 people found this instruction helpful.
  • Robert from PFLUGERVILLE, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexib le dryer tube since the old one had a few holes. It works perfectly again.
Was this helpful?
Thank you for voting!
Bad Motor, Would not start.
3 of 5 people found this instruction helpful.
  • Steve from S LAKE TAHOE, CA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Was this helpful?
Thank you for voting!
Loud banging coming from drum area.
2 of 2 people found this instruction helpful.
  • Larry from S ROCKWOOD, MI
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!
Was this helpful?
Thank you for voting!
Blower (fan) assembly and old model motor with different electrical connections
2 of 3 people found this instruction helpful.
  • Dana from RESTON, VA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatu ral

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Was this helpful?
Thank you for voting!
Fan blade had to be removed , was broken off from motor.
2 of 3 people found this instruction helpful.
  • James from Colorado Springs, CO
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this helpful?
Thank you for voting!
Dryer tumbler made a loud noise
2 of 3 people found this instruction helpful.
  • jeff from albuquerque, NM
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
drum support roller was squeaking VERY loud
2 of 3 people found this instruction helpful.
  • joe from southgate, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this helpful?
Thank you for voting!
The dryer would not heat up
3 of 6 people found this instruction helpful.
  • William from Canyon Country, CA
  • Difficult
  • 1- 2 hours
  • Screw drivers, Wrench set
I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people found this instruction helpful.
  • katherine from Salem, OR
  • Easy
  • 15 - 30 mins
  • Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people found this instruction helpful.
  • Josh from Madill, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people found this instruction helpful.
  • Laszlo from Vienna, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
Worn bushing on bottom drum roller
3 of 6 people found this instruction helpful.
  • Frank from Avon, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people found this instruction helpful.
  • Charles from Cape Girardeau, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Was this helpful?
Thank you for voting!
All Instructions for the 1106507821
106 - 120 of 397