1106117203 Kenmore Dryer - Instructions

All Instructions for the 1106117203
106 - 120 of 187

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic door latch was cracked.
0 of 1 people found this instruction helpful.
  • David from Kohler, WI
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.
Was this helpful?
Thank you for voting!
Dryer door would not close
0 of 1 people found this instruction helpful.
  • Felipe from Helotes, TX
  • Really Easy
  • Less than 15 mins
Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!
Was this helpful?
Thank you for voting!
Dryer won't start!
0 of 1 people found this instruction helpful.
  • Richard from Paradis, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Googled dryer won't start! From information on the Parts Select website, I determined it was possibly the dryer door switch. Checked the dryer to confirm status of door switch and found it broken! Ordered part and received it within 2 days (actually ordered on a Sunday and it shipped on Monday with receipt on Wednesday. Unpluged the drye r. Used information from Parts select website to remove two screws from vent filter, used screwdriver to pop the top of dryer at each front corner, removed two long screws from the old switch and replaced the broken actuator on the switch with the new actuator received from Parts Select. Note: It was easier to remove old switch with the wires removed from terminals (just pull off), replacing the wires after securing the switch and actuator back in place. Piece of cake, wife happy, received her king of the roost reward :>)) This is also a good time to clean the lint filter area and the hoses to prevent one of those 16,000 annual dryer fires!!!
Was this helpful?
Thank you for voting!
Part of the dryer door latch fell out and was lost. Needed to replace it.
0 of 1 people found this instruction helpful.
  • William from Alpharetta, GA
  • Really Easy
  • Less than 15 mins
When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 1 people found this instruction helpful.
  • Tim from Pepperell, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechan ical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)
Was this helpful?
Thank you for voting!
The switch in the door of the dryer was broken so it would keep running when you opened the door
0 of 1 people found this instruction helpful.
  • Matt from Stilwell, KS
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Was this helpful?
Thank you for voting!
Dryer would not turn on, found metal clip in laundry
0 of 1 people found this instruction helpful.
  • Terry from Carlsbad, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's pre ss fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Was this helpful?
Thank you for voting!
door wouldn"t close tightly
0 of 1 people found this instruction helpful.
  • Noreen from Fairfax, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the broken part and replaced with the new one
Was this helpful?
Thank you for voting!
the door catch was broken and I was using duct tape to close the dryer!!
0 of 1 people found this instruction helpful.
  • margery from Lake Spivey, GA
  • Really Easy
  • Less than 15 mins
  • Pliers
This was a classic easy repair and I am sure saved us bundles on a service call.
Was this helpful?
Thank you for voting!
Door would not latch closed when shut
0 of 1 people found this instruction helpful.
  • Carl from Port Arthur, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.
Was this helpful?
Thank you for voting!
broken door catch. door wont close properly
0 of 1 people found this instruction helpful.
  • juan from los angeles, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people found this instruction helpful.
  • linda from las cruces, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people found this instruction helpful.
  • Andris from Sands Point, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this helpful?
Thank you for voting!
The dryer door kept popping open while in use.
0 of 1 people found this instruction helpful.
  • Joseph from Margate, FL
  • Easy
  • 15 - 30 mins
I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to ma ke this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...
Was this helpful?
Thank you for voting!
Door would not latch
0 of 1 people found this instruction helpful.
  • Richard from Millinocket, ME
  • Really Easy
  • Less than 15 mins
  • Pliers
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Was this helpful?
Thank you for voting!
All Instructions for the 1106117203
106 - 120 of 187