- Home
- 1106117203
- Instructions
1106117203 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer door kept opening
1 of 2 people
found this instruction helpful.
-
Jennifer from Big Timber, MT
- Easy
- Less than 15 mins
-
Screw drivers
Popped out the old door catch kit and replaced it with the new one! Easy!!
Was this helpful?
Thank you for voting!
The dryer door catch wouldn't hold the door closed
1 of 2 people
found this instruction helpful.
-
Gerald from Thompsonville, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this helpful?
Thank you for voting!
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
2 of 5 people
found this instruction helpful.
-
Patrick from Ramsey, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on a
... Read more
nd reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
Read less
Was this helpful?
Thank you for voting!
The male part of the door catch was broken
1 of 2 people
found this instruction helpful.
-
David from Chhicago, IL
- Really Easy
- Less than 15 mins
Simply installed the piece and I was done. Took 10 seconds.
Was this helpful?
Thank you for voting!
The latch on my dryer door wasn't working. I was having to shove a towel in the door to get it to stay shut until I was able to repair it.
1 of 2 people
found this instruction helpful.
-
Dan from Lockport, LA
- Really Easy
- Less than 15 mins
All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.
I remember in the "olden days" when I would of had to call a repai ... Read more r guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.
Awesome!
I remember in the "olden days" when I would of had to call a repai ... Read more r guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.
Awesome!
Read less
Was this helpful?
Thank you for voting!
Door wouldn't fasten shut
1 of 2 people
found this instruction helpful.
-
Susan from Laingsburg, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped the latch out and popped a new one in.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
Read less
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people
found this instruction helpful.
-
Daniel from TRENTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said.
... Read more
I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Read less
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people
found this instruction helpful.
-
Rick from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
Clanging of dryer when rolling
1 of 2 people
found this instruction helpful.
-
John from Bel Air, MD
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed video on PartsSelect website, they made it real easy.
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people
found this instruction helpful.
-
Edward from Nanuet, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Door Gasket Broke into pieces
1 of 3 people
found this instruction helpful.
-
Cheryl from Phoenix, AZ
- Really Easy
- Less than 15 mins
It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people
found this instruction helpful.
-
James from Shortsville, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab
... Read more
out 10 minutes.
Read less
Was this helpful?
Thank you for voting!
replace the latch
0 of 1 people
found this instruction helpful.
-
Dennis from Perkasie, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
take the old latch out and pop the new one in. Your repair kit worked perfect.
Was this helpful?
Thank you for voting!
latch not working on Kenmore dryer
0 of 1 people
found this instruction helpful.
-
sally from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people
found this instruction helpful.
-
Mike from Conway, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th
... Read more
e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
Advice: Don't slam the dryer door. The actuator will last longer.
Read less
Was this helpful?
Thank you for voting!