110478 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
screw arm that connects the two hinge parts broke after 15 years
1 person
found this instruction helpful.
-
Phyllis from Ridgefield, WA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Had difficulty getting the door off the washer because I didn't realize there were two hooks in addition to the two screws that held the door to the washer. I reviewed the repair video several times through out the repair. Probably unscrewed more than I needed. Got the new hinge installed on the door. The problem was I couldn't hold
... Read more
the door at the right angle to get the hooks inserted. The washer is near the wall so I couldn't open it all the way and bending over at an odd angle didn't help. At nearly 80 I don't have the strength I used to!! After trying and with the door falling on my arm I gave up and called a friend. We did have difficulty getting the hooks inserted correctly. I held the door and she got the hooks in. On the good side, the hinge part fit like it should!!
Read less
Was this helpful?
Thank you for voting!
water inlet valve leak and hose
2 of 4 people
found this instruction helpful.
-
Paul from Big Torch Key, FL
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people
found this instruction helpful.
-
Jimmy from MEMPHIS, TN
- Very Easy
- Less than 15 mins
-
Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
WASHER WOULDNT DRAIN F21
1 of 2 people
found this instruction helpful.
-
Brenda from PLYMOUTH, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.
Was this helpful?
Thank you for voting!
Washer posting a f6 error
37 of 112 people
found this instruction helpful.
-
Robert from Salt Lick, KY
- Really Easy
- Less than 15 mins
-
Screw drivers
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
Wasn't draining
-
Billie from Dixie, WV
- Easy
- 30 - 60 mins
-
Socket set
Washed three loads and it was ok but then it stopped draining again. I don't know what to do.
Was this helpful?
Thank you for voting!
hole in bellow
-
FAYE from ZEBULON, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You
... Read more
will need the screwdriver to tighten the screws in the inner clamp.
Read less
Was this helpful?
Thank you for voting!
My washing machine started leaking.
-
Barbara from Reno, NV
- A Bit Difficult
- 30 - 60 mins
My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer fails to drain water
-
George from Houston, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs
... Read more
will be purchased here.
Read less
Was this helpful?
Thank you for voting!
Washer leak and tear on clothes
-
Ana from Meriden, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place
... Read more
while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bellow torn at bottom - significant water leak
-
Thomas from Chino HIlls, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.
Was this helpful?
Thank you for voting!
Continous f20 error code
-
James from Yukon, OK
- Easy
- 30 - 60 mins
-
Pliers, Socket set
Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, i
... Read more
t is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Bellows stained
-
Thomas from Chesterfield, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you
... Read more
loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Got the F20 error code
-
Isabella from Rumson, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
A real novice at dyi. Found what the error code meant in the manual and google searched it online. Found Youtube video on repair and was successful in getting the washer to work a few times before the error code returned. Decided to replace the inlet valve and on your site took the advice of a previous user and also changed the flowmet
... Read more
er. Could not have been a better experience. Easy to find the correct parts for my model and got great tips...plus your shipping was excellent. Thanks!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!