110478 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken baffle in washer.
2 of 2 people
found this instruction helpful.
-
Benjamin from N WILKESBORO, NC
- Very Easy
- Less than 15 mins
Inserted new baffle in washer and slide in place.
Was this helpful?
Thank you for voting!
wont pump the water out
3 of 5 people
found this instruction helpful.
-
Paul from Corning, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
Was this helpful?
Thank you for voting!
Bellow leaking water
3 of 5 people
found this instruction helpful.
-
Eric from Vacaville, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this helpful?
Thank you for voting!
Bellow pierced
4 of 8 people
found this instruction helpful.
-
Alexander from Miami, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8.
... Read more
Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.
Read less
Was this helpful?
Thank you for voting!
Washer wouldn't drain
2 of 2 people
found this instruction helpful.
-
Jeff from Barrington, RI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Easily. 4 Screws. 2 Clamps.
Was this helpful?
Thank you for voting!
Tear in door seal
4 of 9 people
found this instruction helpful.
-
sean from Palm Coast, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clam ... Read more p. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clam ... Read more p. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
Read less
Was this helpful?
Thank you for voting!
Washer shook and made noise during spin cycle.
2 of 3 people
found this instruction helpful.
-
Homer from Windham, NH
- A Bit Difficult
- 30 - 60 mins
-
Pliers
Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the
... Read more
old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.
Read less
Was this helpful?
Thank you for voting!
front door leaking
3 of 6 people
found this instruction helpful.
-
jim from winchester, VA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.
Was this helpful?
Thank you for voting!
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
2 of 3 people
found this instruction helpful.
-
Martha from Pine Island, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Was this helpful?
Thank you for voting!
Door would not lock
1 person
found this instruction helpful.
-
Michael from Tonawanda, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Did the repair just like the video on your website. Was really easy.
Was this helpful?
Thank you for voting!
Couldn't be any easier!
1 person
found this instruction helpful.
-
Kimberly from Lake Stevens, WA
- Very Easy
- Less than 15 mins
I am a 63 yr old woman. I was able to remove the washer door, take off the broken hinge, install the new hinge, and place it back on the front of the washer in less than 15 minutes! It is a front load washer and designed for one person to do this. I YouTubed a less that 2-minute video first. The hinge fit perfectly!
Was this helpful?
Thank you for voting!
Machine was leaking from side.
1 person
found this instruction helpful.
-
Suzanne from MENDON, MA
- Really Easy
- 30 - 60 mins
We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!
Was this helpful?
Thank you for voting!
Washer would not fill
1 person
found this instruction helpful.
-
Steve from TULSA, OK
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this helpful?
Thank you for voting!
New baffle would not fit in slots in washer drum. Measuring there is a slight difference in slot openings as compared to new baffles, so was unable to get them inserted. PartSelext very helpful and I'm am to get a credit. Factory to let me know if need to send new baffles back.
1 person
found this instruction helpful.
-
Robert from MARSHALL, VA
- Difficult
- 30 - 60 mins
New baffles would not fit. PartSelect very helpful to get refund.
New baffles should just slide in but did not. Measuring slots and
connection points on new baffles appear to be a difference preventing
connection.
New baffles should just slide in but did not. Measuring slots and
connection points on new baffles appear to be a difference preventing
connection.
Was this helpful?
Thank you for voting!
Door hinge was broken
1 person
found this instruction helpful.
-
Sara from Brier, WA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I followed the directions as given in a video from this site, and it was pretty simple. It can be done without power tools, although I used screw driver heads on a drill. The only iffy part was that some of the star-shaped screw heads were shallow and I had to be careful not to strip them. In brief, the fix required removing the door from
... Read more
the machine, unscrewing the inside of the door from the outside, removing the broken hinge, inserting the new hinge, re-aligning the inside and outside of door, screwing it back together, and re-attaching to the machine.
Read less
Was this helpful?
Thank you for voting!