110478 Kenmore Washer - Instructions

All Instructions for the 110478
91 - 105 of 194

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The washing machine was not draining. It was showing a code on the washer of 02.
3 of 4 people found this instruction helpful.
  • Robin from Gary, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this helpful?
Thank you for voting!
Broken Strike on Washer Door - prevented door from latching, and washer would not start
3 of 4 people found this instruction helpful.
  • David D from Severn, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Was this helpful?
Thank you for voting!
drum baffle broke and had to be replaced
3 of 4 people found this instruction helpful.
  • Alan from GOUVERNEUR, NY
  • Really Easy
  • Less than 15 mins
place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum
Was this helpful?
Thank you for voting!
the pump wasnt puping out the water
3 of 4 people found this instruction helpful.
  • Evette from Mayfield, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this helpful?
Thank you for voting!
Washer leaking
3 of 4 people found this instruction helpful.
  • Carolyn L. from CLAYTON, NY
  • Really Easy
  • 30 - 60 mins
Followed internet instructions
Was this helpful?
Thank you for voting!
Broken hinge
3 of 5 people found this instruction helpful.
  • Kevin from JACKSONVILLE, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Removed screws around door couple around hinge
Was this helpful?
Thank you for voting!
unable to get the correct part
2 of 2 people found this instruction helpful.
  • Russ from DOVER, NH
  • Really Easy
  • 30 - 60 mins
the tabs were to big on the replacement and the customer representitive said he was unable to help me.

discouraged

I will never buy parts from this site again
Was this helpful?
Thank you for voting!
Replacing the heat sensor following an F-24 Error Notice.
2 of 2 people found this instruction helpful.
  • william from VIRGINIA BCH, VA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this helpful?
Thank you for voting!
Water slowly filling the wash drum and spilling out front of machine
2 of 2 people found this instruction helpful.
  • Frank from WEST WINDSOR, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.

Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding t he top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve

NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Was this helpful?
Thank you for voting!
Replace tub to pimp hose.
2 of 2 people found this instruction helpful.
  • Bob from LORAIN, OH
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this helpful?
Thank you for voting!
Error codes SUD and Fo2
2 of 2 people found this instruction helpful.
  • Gregory from LEXINGTON, SC
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump w ith the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
Was this helpful?
Thank you for voting!
Water filling up in drum when not in use
2 of 2 people found this instruction helpful.
  • Don from Oceana, WV
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.
Was this helpful?
Thank you for voting!
Front loader
2 of 2 people found this instruction helpful.
  • Joyime from Wolcott, CT
  • Very Easy
  • Less than 15 mins
Lineup slots and snap in place. So easy even a caveman can do it.
Was this helpful?
Thank you for voting!
Baffle broke off due to drying very heavy garments.
2 of 2 people found this instruction helpful.
  • Lionel from HOCKLEY, TX
  • Really Easy
  • Less than 15 mins
Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.
Was this helpful?
Thank you for voting!
Water leaking in to tub when off
2 of 2 people found this instruction helpful.
  • James from CHERRY VALLEY, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Replaced faulty part
Was this helpful?
Thank you for voting!
All Instructions for the 110478
91 - 105 of 194