110459 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tub would get out of balance on the spin cycle
2 of 2 people
found this instruction helpful.
-
Kirk from P C BEACH, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
UNPLUG WASHER ,SLIDE WASHER OUT FROM THE WALL. TAKE THE BACK OFF ,THEN TAKE PANET OFF IN THE FRONT. TWIST OLD SHOCKS ON THE TOP FIRST THEN TWIST BOTTOMS AND THE SHOCK WILL CUM OUT. PUT NEW SHOCK IN BOTTOM FIRST TWIST TILL YOU HEAR OR FEEL THE SHOCK SEAT ITSELF THEN INSTALL ON THE BOTOOM OF THE TUB.
Was this helpful?
Thank you for voting!
Replace tub to pimp hose.
2 of 2 people
found this instruction helpful.
-
Bob from LORAIN, OH
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this helpful?
Thank you for voting!
Bellow pierced
4 of 8 people
found this instruction helpful.
-
Alexander from Miami, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8.
... Read more
Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.
Read less
Was this helpful?
Thank you for voting!
Water constantly leaking into the washer
2 of 2 people
found this instruction helpful.
-
Timothy from LAS VEGAS, NV
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the ins
... Read more
ide. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.
Read less
Was this helpful?
Thank you for voting!
Broken baffle in washer.
2 of 2 people
found this instruction helpful.
-
Benjamin from N WILKESBORO, NC
- Very Easy
- Less than 15 mins
Inserted new baffle in washer and slide in place.
Was this helpful?
Thank you for voting!
Water leaking in to tub when off
2 of 2 people
found this instruction helpful.
-
James from CHERRY VALLEY, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced faulty part
Was this helpful?
Thank you for voting!
Baffle broke off due to drying very heavy garments.
2 of 2 people
found this instruction helpful.
-
Lionel from HOCKLEY, TX
- Really Easy
- Less than 15 mins
Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.
Was this helpful?
Thank you for voting!
wont pump the water out
3 of 5 people
found this instruction helpful.
-
Paul from Corning, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
Was this helpful?
Thank you for voting!
Error codes SUD and Fo2
2 of 2 people
found this instruction helpful.
-
Gregory from LEXINGTON, SC
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump w
... Read more
ith the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
Read less
Was this helpful?
Thank you for voting!
Water filling up in drum when not in use
2 of 2 people
found this instruction helpful.
-
Don from Oceana, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.
Was this helpful?
Thank you for voting!
Failing inlet valve allowed water accumulation when off
2 of 2 people
found this instruction helpful.
-
Robert from SCOTTSDALE, AZ
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Easiest repair on 2003 front loading washer. This unit cleverly uses star tool machine screws with a hex head so you can pick your favorite tool. Turn off the water supply. Remove the hot and cold hoses at the inlet valve, draining any water into a small bucket. Have a towel for dribbles. *This is a good time to examine the hoses and repl
... Read more
ace them if they are anything other than perfect. Burst or leaking hoses is the #1 cause of water damage in homes.* Three screws releases the top cover which slides 1/2 inch back and lifts off easily. Remove one screw securing the inlet valve (same size screw as the others). Pull the old inlet valve away from the rear panel for easier access. Remove the 4 wires from the solenoids (they pull straight off but maybe need a little finesse), and re-attach to the new inlet valve. Using pliers, release the hose clamp on the old valve sliding it down a couple of inches, then move the hose to the new valve and reposition the hose clamp. Toss the old inlet valve in the trash, screw the new one in place, replace the top panel, reattach and hand-tighten your hoses, turn on the water, look for any leaks, and go have a three martini lunch with the money and time you saved.
Read less
Was this helpful?
Thank you for voting!
Washer wouldn't drain
2 of 2 people
found this instruction helpful.
-
Jeff from Barrington, RI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Easily. 4 Screws. 2 Clamps.
Was this helpful?
Thank you for voting!
original door hook broke in two pieces.
2 of 3 people
found this instruction helpful.
-
carlos from TAMPA, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this helpful?
Thank you for voting!
Tear in door seal
4 of 9 people
found this instruction helpful.
-
sean from Palm Coast, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clam ... Read more p. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clam ... Read more p. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
Read less
Was this helpful?
Thank you for voting!
Water leaking past shut off valve (solenoid operated)
2 of 3 people
found this instruction helpful.
-
Anwar from Pleasanton, CA
- Easy
- 30 - 60 mins
-
Wrench (Adjustable)
Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to ... Read more turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to ... Read more turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.
Read less
Was this helpful?
Thank you for voting!