110459 Kenmore Washer - Instructions

All Instructions for the 110459
91 - 105 of 252

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water would accumulate in the washer drum over several days of non use
4 of 5 people found this instruction helpful.
  • Ronald from RUSSIAVILLE, IN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Repair was very simple. First watch the video that is available on this website. The installation went exactly like the video described. I pulled the washer away from the wall a few inches. Removed the three screws that hold the top on. Removed the top. Shut off the water and removed the water lines. Removed the single screw that h olds the inlet valve in place (T20 torx).Removed the inlet valve, removed the hose from the valve. Reversed the operation to re-install. About a 20 minute job, tops. Tested the washer when finished and it worked great. It has been a couple of weeks now and no water has accumulated in the drum.
Was this helpful?
Thank you for voting!
Bent slide on pedestal
5 of 8 people found this instruction helpful.
  • Donald from Greenfield, WI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A sl ot in the slide mates with a tab to hold the back side of the slide in place.
Was this helpful?
Thank you for voting!
The door bellows had a cut in it
4 of 5 people found this instruction helpful.
  • Arthur from MORGANTOWN, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this helpful?
Thank you for voting!
Ripped bellowspul
4 of 5 people found this instruction helpful.
  • WILLIAM from REPUBLIC, MO
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this helpful?
Thank you for voting!
Bellow was damaged,water leakage.
5 of 8 people found this instruction helpful.
  • Gopaul from Queens, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this helpful?
Thank you for voting!
Spring balanced tub violent shake on spin
4 of 5 people found this instruction helpful.
  • Paul from TARPON SPGS, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement bro ke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people found this instruction helpful.
  • Helen from NASHUA, NH
  • Really Easy
  • 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
3 of 3 people found this instruction helpful.
  • anthony from EASTPOINTE, MI
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was do ne.
Was this helpful?
Thank you for voting!
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
3 of 3 people found this instruction helpful.
  • john from YARDLEY, PA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Socket set
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Was this helpful?
Thank you for voting!
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
3 of 3 people found this instruction helpful.
  • Dennis from AUSTIN, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disc onnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this helpful?
Thank you for voting!
Replace Bellows between door and tub
5 of 9 people found this instruction helpful.
  • Gerald from Douglas, AL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Was this helpful?
Thank you for voting!
The video supplied by you was great and it worked very well.
3 of 3 people found this instruction helpful.
  • Michael from NEWBERG, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
It was fast and pretty easy to do.
Was this helpful?
Thank you for voting!
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
3 of 3 people found this instruction helpful.
  • scott from DENVER, NC
  • Really Easy
  • Less than 15 mins
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Was this helpful?
Thank you for voting!
Tub filling when power was off due to inlet valve leak.
3 of 3 people found this instruction helpful.
  • Francisco from DELTONA, FL
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Followed instructions as shown on repair video at site.
Was this helpful?
Thank you for voting!
tub would not turn
3 of 3 people found this instruction helpful.
  • claude van from big sandy, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this helpful?
Thank you for voting!
All Instructions for the 110459
91 - 105 of 252