110459 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pump not working
4 of 6 people
found this instruction helpful.
-
Darrell from Lady Lake, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced pump
Was this helpful?
Thank you for voting!
door would not latch , and lights on front just flashed
5 of 9 people
found this instruction helpful.
-
FRANCIS from leesburg, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the
... Read more
reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.
Read less
Was this helpful?
Thank you for voting!
Small water leak into washer when not being used
4 of 6 people
found this instruction helpful.
-
Thomas from Dallas, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged and disconnected water lines. Removed three machine screws on the back edge of the washer top. Lifted the back and then pulled it to release it from the front. Removed 1 screw from the back next to the hot water connection. Slide the water valve assembly over to the left if you are standing in front of the washer and it pops
... Read more
out. Then slide the hose clamp for the small hose off and use flat head screw driver to pry hose loose. Then use flat head to gently work connectors off. Then reinstall everything in reverse order. Reconnect water lines turn on water and watch water leaks before cover is reinstalled.
Read less
Was this helpful?
Thank you for voting!
Low water flow into dispenser and washer tub
3 of 3 people
found this instruction helpful.
-
Daniel from WAKE FOREST, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Super simple repair, videos on this site were spot-on.
1. Turn off water, unplug washer, and disconnect the hoses from the back of the washer.
2. Remove the three T20 torx screws holding on the top of the washer, slide the top back about an inch, and lift off.
3. Remove the T20 torx screw holding the water valve to ... Read more the back plate of the washer.
4. Using pliers, release the hose clamp on the outlet hose of the valve and slide it down about an inch.
5. Remove the old valve and attach the new one to the outlet hose. Reinstall the hose clamp.
6. Replace the screw that holds the valve to the back plate and reinstall the top of the washer. Reconnect hoses the the washer, turn on water, and plug back the washer back in.
7. Odds are, your water flow has been low for a while and the first cycle is going to flush a good bit of mildew and other gunk into the washer drum. Run a cleaning cycle with about 1/3 cup bleach through the washer prior to using.
Should be good to go!
1. Turn off water, unplug washer, and disconnect the hoses from the back of the washer.
2. Remove the three T20 torx screws holding on the top of the washer, slide the top back about an inch, and lift off.
3. Remove the T20 torx screw holding the water valve to ... Read more the back plate of the washer.
4. Using pliers, release the hose clamp on the outlet hose of the valve and slide it down about an inch.
5. Remove the old valve and attach the new one to the outlet hose. Reinstall the hose clamp.
6. Replace the screw that holds the valve to the back plate and reinstall the top of the washer. Reconnect hoses the the washer, turn on water, and plug back the washer back in.
7. Odds are, your water flow has been low for a while and the first cycle is going to flush a good bit of mildew and other gunk into the washer drum. Run a cleaning cycle with about 1/3 cup bleach through the washer prior to using.
Should be good to go!
Read less
Was this helpful?
Thank you for voting!
the pump wasnt puping out the water
3 of 4 people
found this instruction helpful.
-
Evette from Mayfield, NY
- Easy
- 15 - 30 mins
-
Pliers, Socket set
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this helpful?
Thank you for voting!
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
4 of 7 people
found this instruction helpful.
-
Keith from Amherst, OH
- Easy
- 15 - 30 mins
-
Screw drivers
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into plac
... Read more
e and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Read less
Was this helpful?
Thank you for voting!
water was back filling into the tub when not in use
3 of 4 people
found this instruction helpful.
-
Larry from BONAIRE, GA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it t
... Read more
o the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.
Read less
Was this helpful?
Thank you for voting!
drum baffle broke and had to be replaced
3 of 4 people
found this instruction helpful.
-
Alan from GOUVERNEUR, NY
- Really Easy
- Less than 15 mins
place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum
Was this helpful?
Thank you for voting!
The washing machine was not draining. It was showing a code on the washer of 02.
3 of 4 people
found this instruction helpful.
-
Robin from Gary, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this helpful?
Thank you for voting!
I find water in the drum after a few days of non use
3 of 4 people
found this instruction helpful.
-
Anthony from Brooklyn, NY
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.
Was this helpful?
Thank you for voting!
Washer leaking
3 of 4 people
found this instruction helpful.
-
Carolyn L. from CLAYTON, NY
- Really Easy
- 30 - 60 mins
Followed internet instructions
Was this helpful?
Thank you for voting!
Bellow leaking water
3 of 5 people
found this instruction helpful.
-
Eric from Vacaville, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this helpful?
Thank you for voting!
Replacing the heat sensor following an F-24 Error Notice.
2 of 2 people
found this instruction helpful.
-
william from VIRGINIA BCH, VA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" ... Read more into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" ... Read more into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Read less
Was this helpful?
Thank you for voting!
Water slowly filling the wash drum and spilling out front of machine
2 of 2 people
found this instruction helpful.
-
Frank from WEST WINDSOR, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding t ... Read more he top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding t ... Read more he top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Read less
Was this helpful?
Thank you for voting!
Washer had a 'thunk' sound during washing. I removed the back and saw the broken shock.
2 of 2 people
found this instruction helpful.
-
Jeffrey from Bothell, WA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
1. After ordering I watched the video on the page for the part, the guy showed exactly what to do.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a li ... Read more ght load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.
Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a li ... Read more ght load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.
Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
Read less
Was this helpful?
Thank you for voting!