11044 Kenmore Washer - Instructions

Repair was very simple. First watch the video that is available on this website. The installation went exactly like the video described. I pulled the washer away from the wall a few inches. Removed the three screws that hold the top on. Removed the top. Shut off the water and removed the water lines. Removed the single screw that h ... Read more olds the inlet valve in place (T20 torx).Removed the inlet valve, removed the hose from the valve. Reversed the operation to re-install. About a 20 minute job, tops. Tested the washer when finished and it worked great. It has been a couple of weeks now and no water has accumulated in the drum.

Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A sl ... Read more ot in the slide mates with a tab to hold the back side of the slide in place.

First I removed the remain remaining baffle using a screw driver to gently pry and break the plastic tabs which held it to the drum. I replaced all three in the event that the balance could be affected if I were to only replace the broken ones. The replacements slid in and locked into place easily but I did have to gently apply pressure w ... Read more ith a large-shanked screwdriver using the rear of the drum to push off of. The hardest part was being able to see what I was doing inside of the dark tub! I needed an extra hand to hold a flashlight. I then discovered the worth of my black and Decker light bar which has a magnetic base! Perfect for the job!
I agree with an earlier post that there is no need to suffer the effects of a washer with a missing baffle when you can replace it so easily.

I have a new faucet so I remove the screen then I used an extender ring put on your adapter an got the washer to run.

Replaced pump

take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.

1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the ... Read more reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Unplugged and disconnected water lines. Removed three machine screws on the back edge of the washer top. Lifted the back and then pulled it to release it from the front. Removed 1 screw from the back next to the hot water connection. Slide the water valve assembly over to the left if you are standing in front of the washer and it pops ... Read more out. Then slide the hose clamp for the small hose off and use flat head screw driver to pry hose loose. Then use flat head to gently work connectors off. Then reinstall everything in reverse order. Reconnect water lines turn on water and watch water leaks before cover is reinstalled.

It was fast and pretty easy to do.

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip

Removed the old hoses and screwed on the new hoses.

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was do ... Read more ne.

Followed internet instructions

Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.