11043 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not continuously heat, and took several cycles to dry clothes. The flame would ignite and heat the dryer at first, but then would ignite and go out quickly for the rest of the cycle. I tried the thermostats first with no luck.
31 of 36 people
found this instruction helpful.
-
Ryan from Livonia, MI
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wir
... Read more
es connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.
Read less
Was this helpful?
Thank you for voting!
Movers wouldn't accept washer w/o shipping bolts
30 of 33 people
found this instruction helpful.
-
Rob from Yakyma, WA
- Easy
- Less than 15 mins
-
Socket set
Like most folks, my daughter has tossed the shipping bolts after her puechase, I moved her the first time w/o any thought to it but commercial movers won't do that, they will chg. you to have it done and it's not cheap, akin to an appliance repair. This kit contains all four bolts/spacers, (2) upper and (2) lower. Hard to tell from the de
... Read more
cription but a sweet gal on the help desk assured me of it. Got it fast and got them installed in minutes, easy to do and wrote a big note on the back of the washer to save them!! No idea why your owners book says "do not reuse".
Read less
Was this helpful?
Thank you for voting!
Bellow torn on HE3t Kenmore
37 of 55 people
found this instruction helpful.
-
Bruce from Tucson, AZ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Take off 3 screws at back of top panel and remove. Remove screw to the left of the soap dispenser and push tab on the right inside the machine to remove control panel and lay the panel on top of the machine without disconnecting. Remove 3 screws on the bottom to remove the bottom panel. You have to pull a bit hard to get it off. Remove 3
... Read more
screws to push through the door lattch and safety switch. Push the window washer nozzle head through the bellow along with the soap feed nozzle.Remove the retainer wire/spring from the bellow where it attaches to the middle panel/inlet. Remove two screws at the top of the middle panel and two screws on the bottom to remove the middle panel with door attached. Loosen the retainer strap ( a large hose clamp) which anchors the bellow to the tub. Remove the plastic nozzle from the window wash hose and mount it in the new bellow. I couldn't get the plastic retainer washer off the nozzle but managed to seat the bello between the washer and the nozzle anyway. Connect the hoze to the nozzle making sure it's pointed in the correct direction. Pull the oblong soap dispenser nozzle into the corresponding bello opening. Seat the bellow around the internal tub opening and place the large hose type clamp, after unthreading it, around the bellow and tighten. Install the middle panel and attach the door latch and safety switch. Now seat the front part of the bellow to the middle panel and attach the retainer hoop/spring. This is a little tricky. I moistened the front rim of the bellow so the hoop would slide over the edge better. You have to stretch the spring to get it to seat properly. Having experience changing bicycle tires helps. Then install the control panel and other panels.
Read less
Was this helpful?
Thank you for voting!
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people
found this instruction helpful.
-
Monique from Mission Viejo, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
no heat
31 of 40 people
found this instruction helpful.
-
rex from streator, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
32 of 44 people
found this instruction helpful.
-
Glenn from Las Vegaas, NM
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Had to take the entire front of the washer off to replace the door latch.
Was this helpful?
Thank you for voting!
Torn bellow. Water leaking
29 of 35 people
found this instruction helpful.
-
krista from scotts valley, CA
- A Bit Difficult
- More than 2 hours
-
Screw drivers
I found a you tube video with step by step instructions. Very easy to follow. Repair would have been quicker had my kids not been at home. I had to have my boyfriend help me put on the outer bellow spring clamp, as I was not strong enough. Washer works great.
Other Parts Used:
Was this helpful?
Thank you for voting!
Water would not drain, motor died
27 of 31 people
found this instruction helpful.
-
Michael from Worcester, MA
- A Bit Difficult
- 15 - 30 mins
Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnec
... Read more
t the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.
Read less
Was this helpful?
Thank you for voting!
belt came off
30 of 43 people
found this instruction helpful.
-
wendy from Naples, FL
- Easy
- 15 - 30 mins
-
Socket set
Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.
Other Parts Used:
Was this helpful?
Thank you for voting!
Door would not lock
25 of 29 people
found this instruction helpful.
-
Tina from petersburg, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.
Was this helpful?
Thank you for voting!
error F 11. Mashine would not run
27 of 36 people
found this instruction helpful.
-
Christina from Englewood, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.
Was this helpful?
Thank you for voting!
door lock was broken
31 of 49 people
found this instruction helpful.
-
Johnny from Homestead, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench
Was this helpful?
Thank you for voting!
dryer stoped heating
23 of 26 people
found this instruction helpful.
-
valerie from Elasmore, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
shaking washer
33 of 57 people
found this instruction helpful.
-
Dean from Morrisville, NC
- Really Easy
- 15 - 30 mins
-
Pliers
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though
Was this helpful?
Thank you for voting!
Washer would not spin ( F-02 comes on)
21 of 23 people
found this instruction helpful.
-
Steve from Dubuque, IA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remo ... Read more ve 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remo ... Read more ve 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.
Read less
Was this helpful?
Thank you for voting!