11043 - Instructions

PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are ... Read more located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.

The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will fin ... Read more d a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.

The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.

Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.

Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.

Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.

Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.

Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w

(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout i ... Read more n the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas

There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils ... Read more & the problem was corrected.

1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.

Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or ... Read more dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.

Pulled out machine...removed top panel..unscrewed existing valve and removed it...then reversed the whole process with the new valve..it was very easy to do and worked perfectly...no more water in tub!

Determining the problem was the hardest part. With multiple parts (coils,thermostats...)possibly causing similar symptoms, I narrowed it down to the two coil valves.
Un plug the dryer. Remove two screws at the base of the front panel. Turn the front panel 180 degrees to avoid disconnecting the door switch. Gas valve with coils on top ... Read more are on the right in front. Remove two screws in bracket holding coils, disconnect the wires, replace with new coils and reconnect wires. One coil has 2 terminals the other has 3 no chance of crossing the wires. I used an offset/right angle screw driver for one of the bracket screws due to close proximity to the drum. A stubby phillips head will work. You can check the burner operation with the front panel off as long as the door switch is still attached. Swing the front panel around and lift back into place securing with the two screws. Dryer works fine now.

I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the ... Read more washer was back in service.

First, unplug the power cord to avoid electric shock!

Then:
1. Open the drawers in the sub-base, remove the screws on the left and right side rails, and remove the drawer.

2. Remove the three torx head screws along the bottom of the front cabinet cover and remove the cover.

NOTE: There are sharp meta ... Read more l edges exposed inside of the cabinet. A heavy long sleeve shirt and gloves are recomended when working in this area to prevent injury.


3. With a pair of pliers, grip the end of the front right shock absorber near the attachment point and rotate counter-clockwise. Repeat procedure at other end of shock absorber. (note: this may destroy the plastic end of the shock absorber, but you're going to replace it with a new one anyway.)

4. With the front shock absorber out of the way, you can now reach the rear shock absorber on the same side and repeat the removal procedure. (note: Be sure to take note of which end of the shock absorber is up and which end is down. This will be important when installing the new ones.)

5. Install the new rear shock absorber by first inserting the lower end into the slot in the base plate and rotating it 1/4 turn clockwise by hand. it should snap into place easily. Then insert the upper end into the plastic drum attachment point and rotate it 1/4 turn clockwise.

6. Install the new front shock absorber by the same procedure, then procede to the left side shock absorbers using steps 3, 4, & 5.

Note: While the cabinet is open, now is a good time to clean out the pump strainer located front and center.

7. Re-install the front cabinet cover using the three torx head screws. (note: the machine will not operate without the cabinet cover in place.)

8. Adjust the leveling legs so that the machine is level and each leg supports an equal amount of the machine's weight.

9. Reinstall the sub-base drawer and plug in the power cord.

First I removed the screws and the plastic slide clips to remove the back plate. I then went to the lower right of the washer and found the motor control unit. It has about four plus going into it. The front inside mount of the control unit has a clip on it that must be pushed so you can pull the unit free of the bottom of the machine. ... Read more Once the control unit was free I flipped open the plug cover with a screwdriver which just snaps over the plugs. I then removed the plugs from the unit carefully so I didn't break them. It was a tight work space and I had to pop out some of the clips that hold the wire harness in place to get some slack in the wires. I then pushed up on the washing drum which gave me enough room to slide to old unit out and get the new one in. Then just reconnect the plugs, plug cover, snap the unit back into place, refit and wire harness clips that where removed, and place the back panel of the machine back on. I tested mine before putting the back panel on and it completely solved the problem. Note that there are 2 control units in this machine 1. motor control and 2. the central control located behind the display. I was told it could have been either one of them, but after some research I chose the motor control unit since it seemed to be a problem with the tachometer sensor which is read through the motor control unit.

I removed the two screws holding the front panel to expose the lower works and verified the heating cycle failure. After a check of the vent system, checking the sensors for continuity and coils for resistance, I retired to the 'net for support. Accepting the general consensus that the most frequent, common and likely failure to be the c ... Read more oils, I rechecked them with the meter and found the two pronged coil to have significantly more resistance than the three prong coil. That was enough evidence to point to the coils. While I waited for the part to arrive, I replace the vent ducting. When the parts arrived I removed the two Phillips screws holding the coils, removed the old ones, installed the new ones, replaced the bracket, put the front cover back on and in less then ten minutes clothes where drying.

I removed the outer tub clamp using two needle-nosed pliers. Then I folded the bellow back and removed the bellow from the dispensing outlet. I then losened the bellow clamp using a screw driver. It was on there very securely. Then I had my daughter with her smaller hands finish untightening the screw enough to release the bellows from th ... Read more e machine. Then the bellow and clamp were taken out of the machine carefully, not scratching anything and noting orientation for new bellow. I cleaned the machine surfaces. Next, lining up the top notch on the bellow, it was worked into the groove around the entire inner basket. The bellow also had to have the hole covering placed over the dispensing outlet. This was the most time consuming. Just to make certain that it was positioned correctly took 20 minutes. I then put the bellow clamp back on and tightened it to the very tight positioned it was in prior to being removed. My daughter returned to help with the smaller bellow clamp that goes to the front of the machine. I needed help keeping one side of the clamp in placed while the other side was stretched out again to go onto the bellow. Then the machine was leveled top to back, side to side, leg nuts tightened. Works quieter than ever.

1 Unplug power.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Look ... Read more ing inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.

Don't know how they managed to get out of the washer tub, but we found a quarter, dime and penny in the "lint" filter (called the "Cap" in the PartSelect details). The penny managed to get into the impeller and took out 3 1/2 of the 4 impeller blades.

Replacement is very simple, about a 15-20 minute job Be sure the machine is u ... Read more nplugged for safety.Remove the three (3) screws holding the lower front panel and remove the panel. The pump assembly is a white unit about the middle of the opening (the original pump itself was black, the new one is white). Unscrewing the large cap will allow any residual water to drain out (we used a wet/dry shop vac to get most of the water out of the tub first). Following the wires going to the pump, there is a cover over the wiring connector that easily pops up and the connector can be pulled out. Directly below the unit is a screw with a Torx head that has to be removed, then two (2) hoses held with compression hose clamps that need to be removed with pliers. The unit will slide out of the base of the washer. There is a wiring harness in front of this assembly that can be popped loose on one side or the other to get the unit out.

Reversing the steps gets everything back in place.

NOTE: A notice came with my new pump stating that a tab needed to be removed on the wiring connector. It is easily removed by hand.

By the way - that was the most expensive penny I've ever owned! Pockets in jeans are now required to be turned out in our house before they are allowed in the washer!