11042826200 Kenmore Washer - Instructions

I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to ... Read more turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires ... Read more the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

Removed covers per instruction video provided by website

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Follow the video when you find the part. It's spot on, exactly what you see and can expect.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Went to google; found a uTube video, plus instructions. Followed it and did the repair in a little over an hour.

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Go to u tube video gives instructions. Very easy to replace

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring ... Read more on hose. Removed hose from valve outlet. Reversed process to install new valve.

The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identi ... Read more fy parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!