11031 Kenmore Washer - Instructions

All Instructions for the 11031
46 - 58 of 58

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not Agitate
2 of 2 people found this instruction helpful.
  • Scott from HILBERT, WI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Tip the washer on its back remove the agitator install new one under 15 minutes
Was this helpful?
Thank you for voting!
Washer would not step through the cycle steps, would not complete the washer cycle.
2 of 2 people found this instruction helpful.
  • Walter from CLAYTON, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.

Problem is resolved, saved almost $250 by doing it myself!
Was this helpful?
Thank you for voting!
The wash plate cap was broken and had to be replaced.
2 of 3 people found this instruction helpful.
  • norvin from SOMERSET, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I used a small flat head screwdriver inserted into slots just under the cap and pried off the cap. The cap should come off very easy.
Replace with the new cap.
Was this helpful?
Thank you for voting!
Reolaced actuator
2 of 3 people found this instruction helpful.
  • Thomas from New Fairfield, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people found this instruction helpful.
  • Shane from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this helpful?
Thank you for voting!
Every load was out of balance no matter how small.
1 person found this instruction helpful.
  • Scott from Rogersville, TN
  • Easy
  • 30 - 60 mins
  • Nutdriver
I watched a YouTube video on the model of my washing machine and repeated the process.
The video helped a lot on how the top came off. Each brand can be slightly different.
Was this helpful?
Thank you for voting!
Error asking for water
1 person found this instruction helpful.
  • Joseph from PEABODY, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I took off cover after viewing a video. Price of cake and unhooked all the wires to valve ( in back ) however the tubes that dumps the water in fabric softener and detergent needed to be unhooked with pliers. ( not my field of expertise) . Did get it done still and worked ! But water overflowed into softener tray which needed to be cle aned. It was the whole problem all along for the error codes.
Was this helpful?
Thank you for voting!
Washer lid locking latch that goes down into locking mechanism broke off inside the lock.
1 person found this instruction helpful.
  • Steven from West Chicago, IL
  • Really Easy
  • Less than 15 mins
  • Pliers
I used needle nose pliers to remove the broken piece of the latch from the lid lock and removed the round broken latch assembly from the lid by twisting counter clockwise and removing it from the round inset hole on the underside of the lid.

I then took the replacement latch assembly, inserted it flush in the hole and twiste d it clockwise until it snapped into position. It took less than a minute to fix. The latch is very thin, made of plastic, so I bought two, to have an extra as a backup.
Was this helpful?
Thank you for voting!
Door alignment
2 of 4 people found this instruction helpful.
  • Amy from INMAN, SC
  • Really Easy
  • 30 - 60 mins
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this helpful?
Thank you for voting!
the impellar mechanism wore out so stopped aggitating
3 of 8 people found this instruction helpful.
  • Stephanie from INDEPENDENCE, KY
  • Really Easy
  • 30 - 60 mins
  • Socket set
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this helpful?
Thank you for voting!
Making groaning noise in spin
1 of 3 people found this instruction helpful.
  • Harold from Blaine, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driv en Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people found this instruction helpful.
  • Brian from DREXEL HILL, PA
  • Easy
  • 30 - 60 mins
  • Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
All Instructions for the 11031
46 - 58 of 58