11031 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people
found this instruction helpful.
-
TERRY from WAUKEE, IA
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
W10721967 Splutch Cam Kit
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.
When I took off the 13mm ... Read more nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.
Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.
Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Read less
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people
found this instruction helpful.
-
Matthew from Wauwatosa, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
Washer wasn't agitating.
5 of 5 people
found this instruction helpful.
-
Darryl from Danville, PA
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and
... Read more
remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.
Read less
Was this helpful?
Thank you for voting!
The original snapped due to it being plastic
5 of 5 people
found this instruction helpful.
-
Davian from Pelion, SC
- Very Easy
- Less than 15 mins
Untwisted it and slipped the new one in quick and easily in less than a minute
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people
found this instruction helpful.
-
Lucas from ARKANSAS CITY, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
screeching noise at times,Wouldn't spin out
4 of 5 people
found this instruction helpful.
-
Jerry from LENGBY, MN
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people
found this instruction helpful.
-
JERRY W. from CARROLLTON, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people
found this instruction helpful.
-
Kristy from Lebanon, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
continually reached FL code
3 of 3 people
found this instruction helpful.
-
Woody from Gordon, GA
- Really Easy
- Less than 15 mins
-
Socket set
Removed Back and top of digit front. removed water intake valve part order new part replacing was a breeze
Was this helpful?
Thank you for voting!
No drain
3 of 3 people
found this instruction helpful.
-
Hoa from Greer, SC
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Take the old one out and put a new one in
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people
found this instruction helpful.
-
Thomas from KENT, CT
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Read less
Was this helpful?
Thank you for voting!
Door strike broke.
3 of 4 people
found this instruction helpful.
-
Derrick from WILSON, NC
- Very Easy
- Less than 15 mins
It easily installed with a twist lock removal and installation. 2 minute fix.
Was this helpful?
Thank you for voting!
Needed to extend drain hose to reach drain
3 of 4 people
found this instruction helpful.
-
Emmett from WEATHERFORD, TX
- A Bit Difficult
- More than 2 hours
-
Socket set
Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose.
... Read more
The hose clip could then be tightened without deforming the hose. Worked great with no leaks.
Read less
Was this helpful?
Thank you for voting!
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
3 of 5 people
found this instruction helpful.
-
Michael from Cranford, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed the video published on this site
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people
found this instruction helpful.
-
James from PINE MOUNTAIN, GA
- Easy
- 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!