11029802891 Kenmore Washer - Instructions

After calling repair services locally and getting outrageous estimates, just to come and see and telling it will cost at least upwards of $ 150.00, decided to look at fixing it myself. Did not want to buy a new unit, as we are building a new house and wanted time to evaluate a new pair later next year. I wanted to put this unit in the garage of the new house, Partselect site was very informative with the symptoms of the problem and required parts and the best feature was the "how to videos". Watched the videos twice and decided I will give it a try. Ordered the parts, which came promptly despite the Thanksgiving holidays (I had to just handwash some essential clothes only once). Watched the videos again and replaced the cam dogs, which we're completely worn out and in pieces. Next replaced the motor couplings. Had a hard time putting back the washer cover, as I had to jiggle it to align. Washer Works like a charm. Saved $$. Partselect should consider bundling the agitator grease with cam dogs. Did not use any grease as I had none. Overall great satisfaction. Thanks.

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.

to change it was 1,2,3
thank you guys

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

took off the soap dispenser, removed the agitator using a 7/16" socket with an extension. replaced the old top agitator dogs and retaining ring with new ones, re-installed top agitator on bottom, thenput whole assembly back shaft, dropped in bold and tightened. whole experience was fast and simple. the parts came fast and where a perfect fit.

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

Remove softener dispencer, use flat tip screw driver to remove agitator cap, there is a slot, insert flat tip screw driver and pry up, once removed you will see the damaged dogs or cogs, use 3/8 drive ratchet with 10 or 12 inch extention and if memory serves me correct a 9/16 socket, loosen bolt and remove top agitator, there is a thrust washer between bottom and top agitator, it comes in the kit, use a little grease preferrably water resistant grease on top of washer, replace top agitator then the plastic device that the cog are inserted into and tighten bolt, put agitator cover back on with a gentle slap of the palm and reinstall softener dispencer, you are done and cloths will agitate properly again, fairly easy job and washer agitator works like new, great kit, would reccomend.

The machine was not designed for quick repairs. The top, front and sides of the machine are all one piece. I had to remove the screws on the lower back access panel. Then remove the water lines, ground screw and outlet hose. I then had to remove the two screws holding the control panel in place. I then bumped the control panel loose. I could then move the back access panel, which is the entire back of the machine, upward to remove it from the clips, located under the control panel. The back access panel will then move away from the machine about 3-4 inches. From the back of the machine, I then had my son tilt the top and sides of the machine forward, leaving enough space for me to reach through the gap and remove the ground screw from the switch. I could then remove the entire switch by pulling it loose from the clips under the top housing and unplugged it from the connection. I then could attach the new ground wire and holding the new switch in place, I had my son secure the switch to the washer. I then had to clip the new switch along the inside of the housing and plug it in to the connection. We then had to realign the sides of the washer with the base, as we lowered it back into place. Holding them in place, we could then reattach the back access panel, loosely, by replacing the two screws on the lower back panel.. Then, aligning the clips that are located under the control panel, we attached the top of the access panel and tightened the screws at the bottom to secure the entire access panel in place. At this point, we could reattach the control panel, water lines, ground wire and outlet hose. It would have saved about two hours of time if the top of the washer was hinged and could have been tilted back to expose the lid switch and tub. Removing the water lines and the outlet hose also allows water to spill, as the tub drains. PartSelect was extremely quick in getting the switch to me. I ordered it on Friday and it arrived on Saturday morning. With five people in our household, clothes washing is a daily chore. We didn't miss a beat. Now, if the engineers at KitchenAid could use a little common sense in designing their products it would make repairs quicker and with less cleanup.

I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in just a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.

I needed the washer ASAP. I paid extra for the expedited shipping. The parts arrived as promised. I watched the on-line video. I read and followed the included instructions. Removed cap and nut. Pulled out part with "dogs", swapped new dogs and assembly. Re-installed components, I was wary from information gleaned from the video, which warned of proper orientation of "dogs", as they can be inserted backwards. Tightened bolt and re-installed cap. Presto! Repaired washing machine worked as good as new. My coffee didn't even get cold.

Popped off agitator cover discovered worn and broken 'dogs'. Decided to replace complete agitator assembly due to age of machine (25 + years). 7/16 socket, removed nut and agitator assembly, installed new assembly with included nut.

Used screw driver to pop top off to access the bolt on spinning unit.Used socket wrench and took bolt off of bottom of spinniner. Replace agitater with new parts and reassembled. Now it works like new.

Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.